Crunch amps

[Famous_78]

Store for powerbass amps?

 

[DejaWiz 5,000+ posts]

www.millionbuy.com

 

[Famous_78]

# SPECIFICATIONS

* Power Output @ 14.4VDC Input

o 4-Ohms RMS @ THD 0.5% : 500 Watts x 1-Channel

o 2-Ohms RMS @ THD 0.5% : 1000 Watts

o 1-Ohms RMS @ THD 0.5% : 1000 Watts

* Signal-to-Noise Ratio : >80dB

* Frequency Response : 20Hz~250Hz +/-1dB

* Crossover

o Low Pass Filter : 50Hz~150Hz

o Crossover Slope : 18dB

o Subsonic Filter : 15Hz~50Hz

o Bass EQ @ 45Hz : 0~18dB

o Input Gain Control : 0.5V~4.0V

o Low Level Input Impedance : 22,000 Ohms

o Damping Factor : >150 into 4-Ohms

o Fuse Ratings : 40A x 5

o Dimensions (WxHxL) : 11.35" x 1.92" x 17.75"

Not heavy enough for me 2000 watt rms not 1.

 

[Famous_78]

http://www.millionbuy.com/spldk3400d.html

Looks pretty good i got a friend that owns one he has no probs with it.

 

[phantom240 5,000+ posts]

Get two smaller amps nub.

 

[Famous_78]

i dont know how to strap and set 2 of them up or i would.

 

[mike dressure 10+ year member]

# SPECIFICATIONS
* Power Output @ 14.4VDC Input

o 4-Ohms RMS @ THD 0.5% : 500 Watts x 1-Channel

o 2-Ohms RMS @ THD 0.5% : 1000 Watts

o 1-Ohms RMS @ THD 0.5% : 1000 Watts

* Signal-to-Noise Ratio : >80dB

* Frequency Response : 20Hz~250Hz +/-1dB

* Crossover

o Low Pass Filter : 50Hz~150Hz

o Crossover Slope : 18dB

o Subsonic Filter : 15Hz~50Hz

o Bass EQ @ 45Hz : 0~18dB

o Input Gain Control : 0.5V~4.0V

o Low Level Input Impedance : 22,000 Ohms

o Damping Factor : >150 into 4-Ohms

o Fuse Ratings : 40A x 5

o Dimensions (WxHxL) : 11.35" x 1.92" x 17.75"

Not heavy enough for me 2000 watt rms not 1.

the specs you just listed is for the 1000.1 go on ebay and look for the 2000.1 it does 2000 rms at 1 ohm

 

[phantom240 5,000+ posts]

i dont know how to strap and set 2 of them up or i would.

DVC? One on each coil.

 

[Famous_78]

Dual 15's 4 coils how would i do that?

 

[mike dressure 10+ year member]

Dual 15's 4 coils how would i do that?

well in that case run one amp per sub!

 

[Famous_78]

Run 2 powers 2 grounds or how does that work?

 

[mike dressure 10+ year member]

run one large power and have a distro block.....then run 2 smaller peices from the distro, 1 to each amp! then run 2 ground's one for each amp

 

[phantom240 5,000+ posts]

or a distro for the grounds.

In any case, try to find an amp that puts out good power at 4 ohms. Youll be set. Might I recommend alpine MRV-1507s. Theyre sexy loud @4 ohms mono. I speak from experience, I own 2.

 

[Jep772 10+ year member]

**** that powerbass amp looks nice, 5x40a fuse rating, big *** terminals and cheap.

 

[NEXT 10+ year member]

The new Ground Pounder series is killer...test from another guy a another forum

The GP 1600.1 rated to be 800wrms @ 1

power supply at 15.5vdc before burp. (running schumacher 10amp charger)

.18 ohm nominal load

35vac

38amps

.92ohm reactive load

1331 watts

power supply dropped to 12.8vdc during burp.