got original boxes, they're currently installed in my wife's expedition.
looking to unload so I can get either 2 audioque 3500s or a single sound digital 8k possibly...
$275each local pickup or $300ea shipped will do deals on multiples and willing to accept reasonable offers. these are good amps tho so don't expect to get them for free. if your looking at this thread you probably know what these amps are capable of...
I'm currently running them to the AQs .7ohms in strapped pairs run like this daily and I haven't ever had a problem I've run them like this previously in other installs in singles and pairs but this is the 1st time I've had all four in one vehicle due to size this is the 1st car we've had that can fit this much and still have a back seat. I personally gain matched them at 44vv per strapped pair and did a 148.1 on music when I matched them at 44v and did a 149 46hz tone. THEN, I realized I should've matched them higher so I matched them at 78.3v instead. the 148 and 149 were new TL @ dash from the pair of HD3 15"s it's NOT a wall, this was at a local comp on saturday 2hrs after installing it I had no testing done what so ever. anyway, reasonable offers will be accepted/considered. unless you have the amps specified I'm probably not interested in trades as I'm ONLY getting rid of these to pick up less amps so it'll be physically smaller and easier to install and uninstall. as I'm supposed to pull it out when not doing comps since it's the wife's car lol. looking to simplify this and shed some of the size. these amps aren't physically that big but if u multiply it by 4 you get quite a lot of room... boxes will lay side by once I can shrink the setup down enough lol. the batts are HUGE so it's gonna be a pita but I'm trying to get it to be something I can keep as loud but leave it in there from comp to comp, not have to remove it all the time... I'm hoping to get it into the 50s on music. the few people who've heard it since I rematched the gains were impressed/surprised of it's capabilities.. (I was having bad clipping issues with my maxxlink at the comp //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif and one pair was going into protect and I still managed a db away from a 150 lol)
POSSIBLY consider trades for more HD3 motors/subs AMERICAN ones not the china ones.. I don't care if the china ones are louder, I currently have the american ones and am not looking at getting rid of these two to have to get 4 more... unless someone wants to trade subs too LOL.
oh, here's my batts cuz I like to show them off LOL here's them next to a kinetik 2400
here's them adding close to 600lbs to an 07 expedition LOL
can check out my a part way build log and a few of my hardships of it in this thread if u have interest to...
http://www.caraudio.com/forum/showthread.php?t=442798
to the bottom of the page and the next 3 pages and you'll understand why I need to get the size of everything down lol. like I said it's not a wall the boxes are standing as the ports didn't have breathing room once I put the batts in //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif
looking to unload so I can get either 2 audioque 3500s or a single sound digital 8k possibly...
$275each local pickup or $300ea shipped will do deals on multiples and willing to accept reasonable offers. these are good amps tho so don't expect to get them for free. if your looking at this thread you probably know what these amps are capable of...
I'm currently running them to the AQs .7ohms in strapped pairs run like this daily and I haven't ever had a problem I've run them like this previously in other installs in singles and pairs but this is the 1st time I've had all four in one vehicle due to size this is the 1st car we've had that can fit this much and still have a back seat. I personally gain matched them at 44vv per strapped pair and did a 148.1 on music when I matched them at 44v and did a 149 46hz tone. THEN, I realized I should've matched them higher so I matched them at 78.3v instead. the 148 and 149 were new TL @ dash from the pair of HD3 15"s it's NOT a wall, this was at a local comp on saturday 2hrs after installing it I had no testing done what so ever. anyway, reasonable offers will be accepted/considered. unless you have the amps specified I'm probably not interested in trades as I'm ONLY getting rid of these to pick up less amps so it'll be physically smaller and easier to install and uninstall. as I'm supposed to pull it out when not doing comps since it's the wife's car lol. looking to simplify this and shed some of the size. these amps aren't physically that big but if u multiply it by 4 you get quite a lot of room... boxes will lay side by once I can shrink the setup down enough lol. the batts are HUGE so it's gonna be a pita but I'm trying to get it to be something I can keep as loud but leave it in there from comp to comp, not have to remove it all the time... I'm hoping to get it into the 50s on music. the few people who've heard it since I rematched the gains were impressed/surprised of it's capabilities.. (I was having bad clipping issues with my maxxlink at the comp //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif and one pair was going into protect and I still managed a db away from a 150 lol)
POSSIBLY consider trades for more HD3 motors/subs AMERICAN ones not the china ones.. I don't care if the china ones are louder, I currently have the american ones and am not looking at getting rid of these two to have to get 4 more... unless someone wants to trade subs too LOL.
oh, here's my batts cuz I like to show them off LOL here's them next to a kinetik 2400
here's them adding close to 600lbs to an 07 expedition LOL
can check out my a part way build log and a few of my hardships of it in this thread if u have interest to...
http://www.caraudio.com/forum/showthread.php?t=442798
to the bottom of the page and the next 3 pages and you'll understand why I need to get the size of everything down lol. like I said it's not a wall the boxes are standing as the ports didn't have breathing room once I put the batts in //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif
