jrpro130
10+ year member
Get Your Face *****
I got the TCAB 12" Type R Box from Mark Potts on Friday...it was quite massive....for those that don't know him...well, you should!!! He builds awesome boxes //content.invisioncic.com/y282845/emoticons/naughty.gif.94359f346c0f1259df8038d60b41863e.gif
The port is massive
Just a test fit to make sure it fits properly...although i did install it with the back panel on, I ended up taking it off...more on that later
All ready for test fit
Going in
In
Port compared to my i870
I know mark wanted a pic for the TCAB site...your welcome to take this one
got some advertising for ya on the back panel
Ok now more on to the install/fit...It does fit with the back panel still on...yes. But I did loose about 3" of legroom //content.invisioncic.com/y282845/emoticons/crying.gif.ec0ebefe590df0251476573bc49e46d8.gif
So I ripped out the back panel (not literally, but pretty close) and I gained back all my legroom. The part that the jack connects to was in the way, by about 5"...soo i gained all that room back. I'm 6"2...and my seat is ALL the way back. The back of the headrest is at the rear window line...actually a little furthur back. so I didn't lose any legroom at all...exactly what i wanted
It rattles like a TIN CAN...I need to fatmat/dynomat/spray EVERYWHERE and anywhere...thats definetly next on the list. If anyone has a hookup or extra LMK, I need everything, doors, floor, (i don't want the headliner, i have no rattle there) EVERYTHING though (except headliner it's a PITA)
The at 32hz i get about 2" of rear panel flex...i measured this outside with a ruler...i put the ruler on the panel with no music and it was i belive 3" gap between the glass/bedliner. i then played the tone and the ruler went to about 1" reading steady...so thats some pretty good flex
Yes, it is very painful to sit in...I do not think it's a 50...but my body hurts while in the vehicle. It definetly will give you a new hairdo...it's like a low note bass machine...anything below 40hz HURTS at even 75 percent tilt.
The port is massive
Just a test fit to make sure it fits properly...although i did install it with the back panel on, I ended up taking it off...more on that later
All ready for test fit
Going in
In
Port compared to my i870
I know mark wanted a pic for the TCAB site...your welcome to take this one
got some advertising for ya on the back panel
Ok now more on to the install/fit...It does fit with the back panel still on...yes. But I did loose about 3" of legroom //content.invisioncic.com/y282845/emoticons/crying.gif.ec0ebefe590df0251476573bc49e46d8.gif
So I ripped out the back panel (not literally, but pretty close) and I gained back all my legroom. The part that the jack connects to was in the way, by about 5"...soo i gained all that room back. I'm 6"2...and my seat is ALL the way back. The back of the headrest is at the rear window line...actually a little furthur back. so I didn't lose any legroom at all...exactly what i wanted
It rattles like a TIN CAN...I need to fatmat/dynomat/spray EVERYWHERE and anywhere...thats definetly next on the list. If anyone has a hookup or extra LMK, I need everything, doors, floor, (i don't want the headliner, i have no rattle there) EVERYTHING though (except headliner it's a PITA)
The at 32hz i get about 2" of rear panel flex...i measured this outside with a ruler...i put the ruler on the panel with no music and it was i belive 3" gap between the glass/bedliner. i then played the tone and the ruler went to about 1" reading steady...so thats some pretty good flex
Yes, it is very painful to sit in...I do not think it's a 50...but my body hurts while in the vehicle. It definetly will give you a new hairdo...it's like a low note bass machine...anything below 40hz HURTS at even 75 percent tilt.
