Recent content by stikystikyricky

I added an additional Hi-Low converter and hooked the sub amp with rca rather than the speaker cable input. It made a huge difference. Its alright for now.. But the box definitely needs to go. I think im just going to get a JL Stealth box with a jl 10w3v3. And eventually a better amp.

Thanks for the replies. As mentioned the amp is only pushing probably a true 300 rms, well that's all I really need for my single 300 rms 10" sub. And as far as my expectations being too high, my plans aren't to wake up the neighborhood, I just want my bass to hit like I have a 10" sub in...

2013 dodge ram, stock head unit. 4 channel amp being run by hi-lo converter. Sounds Great! Subwoofer however: Kenwood KFC-XW10 1000W 10" Single 4 Ohm (300watts rms) Sub Amp: PLANET audio AC1500.1M (700x1 @ 4ohm) Box: Cheap ebay under the rear seat prefab box. Paid $60 Dodge RAM Quad Crew...

hey, Our parking garage at work has tight spaces and my car has been backed into twice now. I have a dash cam in my car that I have hard wired in however it shuts off when the car is turned off. I am thinking of wiring it to a constant 12v so its always recording but Im worried it might drain my...

In the trunk of my mustang I built a spare tire box with 3 kenwoods 10's. (KFC-W2513PS) 300 rms 4 ohms each. Frequency response: 39-300 Hz Sensitivity: 82 dB. They are wired at wired at 1.33ohms My amp is a planet audio bb2400.1 (2400 rms x 1) My questions.. Input sensitivity: 100m-2v or...

No they are single 4 ohm. 4 subs wired parallel 4ohms each = 1ohm My question is with my amp which is 1ohm stable should I wire 3 subs in at 1.33 ohms or 4 in at 1ohm. The installer said whatever you wire it too, the amp will see half of that. So if I wire 1 ohm the amp will see .05 ohms?? Im...

Hey, I have an 89 mustang convertible and just purchased a fiberglass spare tire enclosure that holds 2 10's side by side. I was originally going to cut two holes on top and mount 4 10's and stuff the box. The 4 10's I purchased are the Kenwood KFC-w2513ps. Wired parallel into 1ohm. The amp...

Hey, I just ordered a single 10" TS-w2502d2 (DVC 2ohm speaker), a Hfi1000.1d amp with bass knob, and a KNUKONCEPTZ 4 gauge amp kit to hook up to my stock bose system in a 2008 escalade. My question: The amp is "rated" at 1000 rms x 1 and 475 rms x 1. The sub is "rated" to handle 800rms...

As far as dimensions go I dont have any specifics. I was just going to draw it out on a piece of mdf and cut width wise and maybe just go 8" deep. The speakers are Cadence CWM-6KIT Aluminum 6.5" Component: NEW Cadence CWM-6KIT Aluminum 6.5" Component Kit | eBay Running a 4channel amp to them...

Hello, I am building a speaker box for a boat. It is going to have 4 compnent speakers ( 4 61/2's and 4 tweeters. The box is going to be rectangle and have it setup side by side something like this. Oo Oo Oo Oo Oo My question: Should I build the box single chambers for each speaker or does...

I have an 08 Tundra with the PPI 365cs mounted in front. The tweets are high up on the dash pointing up towards the windshield. They are alright... Dont get as loud as I would like them too with out distortion. I am running an infinity 475a (75x4 rms) Back speakers are shot and I am purchasing...

Okay.. I will try to make this as simple as possible. I have a 2008 Toyota Tundra. The truck comes stock with 2 front door speakers, 2 dash mounted 3.5" speakers up by the windshield, 1 center channel speaker(empty but I could build a plate if needed), 2 rear speakers. I purchased: 1...

Whats up man... Wanna sell me your amp or what?

IF you have an infinity 475a 4ch amp for sale let me know.. im interested!!! -Rick

Im in the newcastle/renton area.. I have the same speakers up front and in the rear.. I think im just gonna keep an eye out for better front components and when I find them move my front ppi's to the back and get like a nice set of focals or something upfront.. fml.. this blows. i just bought...