Recent content by Sgt. Spuds

I have two sa15's running off of a brz1700. I have the opp to trade it plus a small amount of cash for either a massive audio 2k or a saz1200. What out of the three amps would be best for me? I know the saz is the best quality of the three, im just worried its too small

You will want to run a 4 channel amp and all new speaker wire to the doors. The stock Bose amp is integrated deep in the car and bypassing it ( like mine is now, waiting to install new amp ) you will lose some functionality. If you hook up the aftermarket speakers to the Bose amp you will lose a...

I ended up grabbing a pair of memphis 6.5 mid range ( part of a set of components ) for the rear doors, so I dont have to modify the door as much if at all. May add a cross over and set of tweeters some time in the future.

Idk, they are 4 ohm just like the components and they are rated 10-100 watts rms.

6x9s are 3 way I have the cross overs that the components came with so I was planning on running those and setting the amp to full ( no electronic cross over ) for the fronts. If I run the 6x9s off the amp I may use the electronic cross over settings but I really have no knowledge on how to set...

I have an escalade ( the short tahoe styled one ) my set up is ; (2) Sundown Audio SA-15 Hifonics Brz1700.1D 9 cubes @ 32Hz I have been piecing together the rest of my system. So Far I have the Hifonics TZi4408 & Polk DXI6500 Component Set. These will be going in the front. I had planned...

Grr, thanks for the response! I posted this question on 3 different boards and have gotten both answers lol, some say its bass boost, some say gain... How can I actually test it? I dont think its bass boost, because I have that turned to 0 on the amp, and my subs still bang. When I turn the bass...

I have dug around the internet and looked for an answer to this, and have found somewhere in the neighborhood of a million different theorys. I have my BRZ 1700's gain set properly, and its running my 2 sundowns. I would like to be able to lower the volume of the subs without having to go...

I ended up getting a pair of polk audio dxi6500's for the front. I went and listened to a bunch and they seemed to be the best of the bunch. Will post once they are in. I think Im gonna leave the rears stock, but can I go ahead and plug in my rear channel rcas and run them to the amp but not...

Subs do seemly notably louder though, is that possible or my ears paying tricks on me?

I got my big three done. I used aluminum tinned copper solder on 0 gauge 3/8ths lugs, as I didn't want to trust crimp style ring terminals, and KnuKoncepts KCA 0 gauge to do it all. I honestly don't see any difference. I will upload 2 before and after videos of my stock voltage meter playing the...

My amp is a Hifonics TXi4408, its specs are as follows. 4 ohms: 55 watts x 4 chan. 2 ohms: 110 watts x 4 chan. 2 ohms: 220 watts x 2 chan I am wanting to run at 2 ohm to get the most out of the amp, and that has me looking at infinity components. Infinity Reference 6030cs 6-3/4" component...

Check radioshack, they should have one for under a dollar....

I have bypassed my bose amp, and have an extended speaker wire harness running to my deck, It would be very easy to reverse that and run that harness from the head unit to an after market amp's high level inputs. I could also run two more sets of RCAs from my head unit to the rear, and use the...

Currently have 2003 Escalade with; Stock 145amp Alt ( brand new ) Kenwood DDX419 HU Hifonics BRZ1700.1D (2) SA-15's in a ~9ft^3 ported box tuned to 32 hz 0 Gauge KCA KnuKoncepts Power wire fused ran from positive battery terminal 0 Gauge KCA KnuConcepts Ground wire to Seat Bolt w/ Ring...