Recent content by kylegmoore71

I’m trying to build a box to fit in my daughters Tacoma Access Cab. I was hoping someone could help me out. I’m attaching a photo of some basic drawings/measurements that line it out. Goals. 1.5 cf ported box tuned to 35hz. It will be a Soundqubed HDS310 pushed by 1500 Watts rms. I want the...

Okay, before I get a pile of hate, lol... I am more curious than anything. I have a RF1200 lying around, and I'm thinking of getting an x10, and I was just curious if I could push it with that? If I get the x10 I will follow suit with a scv 2000, but I have to outfit a whole system top to...

Okay, it turns out my daughter is a chip off the old block and she's a bass head, so I'm going to put a system in her truck when she gets it. It's a Toyota Tacoma Access Cab. My question is what you guys would recommend. I've worked the dimensions, and it looks like I can get right at 1.5 cu of...

Ok, So I just threw in a budget system in my beater rig. I've got a RF 1200D1, a RF 400x4 for my mids, and I'm running a pair of Soundquebed hd210's. I'm running 4 gauge OFC throughout, and I've I've completed 2 out of the three, of the big three,(I need to do the engine ground this weekend). I...

what do you suggest? I'm doing a build on my daughters Tacoma and plan on going all sundown. An X-10, and a scv2000 to run it....plus I have to do everything.....deck, doors, etc... so I'm trying to save a little cash. Plus, I'm going to do the big 3 regardless of the amp, and I have to wire...

I'm doing a budget build on my hunting/fishing rig, and I'm looking at grabbing an audiopipe amp. I've seen the youtube Dyno on the APCL1500 pulling close to rated, but I haven't seen anything on the APMI versions. They are within $20 of eachother and it would be nice to save a little room. I...

Do any of you guys know were the engine ground is on a 2003 Ram 1500 with a 4.7? I want to order my big 3 kit, but its raining like crazy and I didn't want to crawl under in a rainstorm,lol.

Ok, so I've jumped into my first fiberglass box....a couple of youtube videos and your an expert right, lol? Ok, so it's not the prettiest, but I did have a couple of quick questions. 1. The box is molded to the actual floor plan, and unfortunately it isn't even from one side of the truck to...

I'm putting a pair of SD3 -12's D4's in a sealed box. About .8 per sub, and I'm trying to narrow down the amp. This is my hunting/fishing truck that I'm just going to get set up because my daughter will be driving it until she get's her ride for her 16th birthday. I'm looking for a solid...

It's going in between the rear jump seats in a Tacoma access cab. The height is like 22"and it'll be rouhly10-12" deep depending on how I build it. I'll try and get a pic up of what I'm going for.

I'm not looking to spend a crazy amount, but my original plan was buy and x10 and a scv2000, so anything around that price would be reasonable. So you think the x8? I'll go hit up the review right now.

Okay, so I'm going to building a box for my daughters Tacoma soon, and I'd love to hear some opinions. I've done some rough measurements, and it looks like I can squeeze about 1.5 cf out of a box, maybe just a touch more. This will be for a daily driver, so I would like middle of the road for...

I'm lookin to build a box in between the jump seats in the back of an access can Tacoma, and I was just curious if anyone had experience or built one in the past. I'm looking to put a single Sundown x8 or x10.

Man, memories! I ran 3 of those in my 84 Monte Carlo in high school. They were the speaker to have back in 97-99 timeframe.

I just called an got the magnet diameter, and mounting specs from your support department, and also got talked into an x-10 for my daughters Tacoma when she gets it. Now I just need to measure the box and make sure they fit. Thanks for the info, and kudos for an awesome support department!