Recent content by Blang

nice thanks for the link Booming and yeah after comparing spec to other drivers I stopped looking at it

so there is a guy locally selling an Audiopipe TXXBD2W18D2 for $250 found spec sheet on it tried to input the spec into bassbox and most of them show red seems like a deal but maybe not I dunno what do you guys think?

So I recently blew a few skar vvx10v2 and I have 3 triple stacks .784 2.5"VC motors and decided screw it I'm just going to attempt to build 3 woofers on these motors looking at the baskets available on the lord of bass and psi. found some coils that will work on these motors nicely..... the...

@shredder2 nice redesign I was actually thinking the same either EVL or DDX and yeah I was playing below tuning at 35 ish and the lows were hitting down to 28hz @audiobaun they are d2 wired at 1.3ohm well I'll just let this die out thanks a lot to Shredder2 he gave me a great redesign...

@Boomin_tahoe I don't think I would go down to 2 10's unless I just pull the 1 that's blown and build a new box prefer not to do that tbh @THATpurpleKUSH this is a sedan (trunk) it is a pain to get the box in and out have to remove back seat upper and lower and the seatbelt...

@nauc I would like to stay with skar but that FI SSD18 looks nice @Jeffdachef 10 cubes sounds way overkill but ok? @kcr357 yes the port area was a bit low for the 3 10's but it was at 37.7in2 with a 5.14cf common chamber it actually sounded good so I left it @audiobaun I do...

i have a 2011 Nissan Versa S its 4 bolts to remove the back seat it can be removed and replaced very easy when the bolt are out completely i had to remove my back seat completely to get my box in the car through the back doors..... yes it was 5.7cubes for my 3 10's it was insane there is a nice...

Hello, guys, I have a dilemma so let me fill in the blanks to give you guys the ability to add input to my issue I daily drive a 2011 Nissan Versa S, I installed a few audio improvements kinda..... anyway I currently have an Atoto android head unit love it, by the way, added a set of component...

using an app on enclosures was mainly playing with port sizes and playing with dimensions and increasing cf based on the amount of space I have availible in my car and that's where I was getting 36 wide and port would have been firing into the cabin

so to much space so 30W 20L 15H with a 4x4x10 slot port nets me 3.6cf so that's 1.8cf per driver and hits 30hz exactly the port area is 16.in² by the way, this is why I'm picking you guys brains because I'm still rather new to building enclosures and joined the forums for help to really get the...

edited post above port area 64.0in² the tuning on that would be 35.1hz do you think that's it's too big for the drivers or should I rethink the size and bring it down to 1.8-2.0 per driver? and to answer why dual 2ohms because I eventually want 3 at 1.33ohm or 4 at 1 ohm

1.6-1.7?? im looking at 2.6 per 5.26cf net 6.51 gross 8x8x20 slot port enclosure will be 36w 24l 16h driver displacement 0.24 port displacement 1.01cf made with 3/4 birch ply i work at a lumber yard and get it at cost

well I have the 1 right now in a 1.85cf tuned at 35 and just the 1 on 700 watts is pretty intense so many people call me a liar when I say its just 1 10" till I show them but I think I'll go with the 2.6 at 35 I just have to deal with not being able to hit the lows lol it's a Hifonics Zeus...

what would you recommend? the manufacturer recommends 1.75 ft^3 per driver I also have a design that is 2.6ft^3 per driver at 35hz

Time to pick you guys brains a little bit again, So I currently have a vvx10 that I have had for about a month and its seems broke in and sounds rather intense at 700 watts but the question I have entails the new enclosure since my new driver will be here this coming week. I plan on building a...