Worst injury while working on your system?

[AltarCrystal 10+ year member]

I mean, we all get our own cuts and brusies, but ever do something notable?

Mine JUST happened a couple hours ago. I had to run speaker wire through my groumet, but I"ll be ****ed if they didn't pack enough wires through the driver side. I figure I could cut a wire hanger and run it through there, attach the wire, and pull it the rest of the way through.

So, I grab a wire hanger and my wire cutters/strippers/crimpers, put the hanger in there, and BAM! Crimpers through my thumb. immeditally blood started pouring through, and I quickly grab eletrical tape to put pressure on it until I can clean it up.

ALMOST bad enough for stiches.

Click to read more...

 

[dumple 5,000+ posts]

a lady friend of mine kicked me in the nuts cuz i wasnt paying any attention to her

 

[AltarCrystal 10+ year member]

a lady friend of mine kicked me in the nuts cuz i wasnt paying any attention to her

...you win //content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif

 

[Twistid 5,000+ posts]

i havent really gotten hurt that bad, but one time i picked up a woofer by the edge near the gasket and my fingers went underneath and while i was carrying it slit the **** out of fingers on the underside against the cone ... like a papercut only with whatever material it was made out of, went deep as crap and hurt whenever i touched anything ...

 

[oxygen65]

i was cutting carpet with some box cutters and they slipped and went strait into the plalm of my hand, it was preaty bad

it was a trip to the emergency room

 

[Beat_Dominator 5,000+ posts]

I pulled my *** getting into my Mustang's trunk upsied-down //content.invisioncic.com/y282845/emoticons/crap.gif.7f4dd41e3e9b23fbd170a1ee6f65cecc.gif

 

[blackbonnie 5,000+ posts]

trying to strip 0 gauge with scissors and slipped and sliced my finger, had to have 6 stitches.

 

[blackbonnie 5,000+ posts]

and while soldering a wiring harness together on my workbench, i was wearing a cutoff t-shirt, and leaned over to grab something, and burnt my right nipple. i burnt it bad.

 

[WantedIsHere]

shot a finishing brad into my hand... lesson learned always watch your hands while using air tools that shoot nails or other sharp objects... didnt hurt half as much going in as it did when i pulled my hand off the wood....

 

[TylerBD12 10+ year member]

I was making a fiberglass amp rack and when i was getting some of the big imperfections with a dremel i slipped and cut my thumb.

I should have gotten stitches

 

[Chevyaudio 5,000+ posts]

I got a pretty decent size cut with a razor blade one time.

 

[ngsm13 5,000+ posts]

I pulled my *** getting into my Mustang's trunk upsied-down //content.invisioncic.com/y282845/emoticons/crap.gif.7f4dd41e3e9b23fbd170a1ee6f65cecc.gif

Buh.

nG

 

[SethPhillips 5,000+ posts]

was doing some grinding on a fiberglass box. grinder jumpped...... now i have a stubby thumb !!! hurt like a *****!! went to ER and all that...

 

[SethPhillips 5,000+ posts]

almost forgoat about the time a ran a 1'' long screw threw my pointer finger.... holding a pice of wood screwing into it!!

that sucked

 

[WantedIsHere]

oh i also dropped my 3.5 foot long bolt cutters that weigh a ton... on my foot when i wasnt wearing shoes or socks. another lesson dont cut 1/0 without shoes on or you might cuss allot in front of your kids....