Will it work?

[hyhat33]

Here are some specs for the stuff I'm buying I wanta make sure it's all going to work before I order it Couldyou tell me if this amp will work with these 2 speakers Please!!!

Amp:

Power MAX (2 Ohm): 800 Watts x 2

Power RMS (4 Ohm): 280 Watts x 2

Bridged Power (4 Ohm Only): 1600 Watts x 1

Tri-Mode Operation: Yes

Remote Subwoofer Level Control: YES

Line Outs: YES

Inputs: Speaker/Line Level

Low Pass Crossover (Variable): 40Hz - 150 Hz

High Pass Crossover (Variable): 120Hz - 400Hz

Bass Boost (Variable): 0 - +18 dB

Treble Boost (Variable): 0 - +12 dB

Signal to Noise Ratio: 105 dB

THD @ RMS Watts: 0.01%

Frequency Response: 9Hz- 50K Hz (+/- 3dB)

Channel Separation: 90 dB

Damping Factor: 125+

Dimensions: 11"W x 2-3/4"H x 21-3/8"

Speakers (there will be 2 of these hooked up to the amp):

RUBATEX GASKET

GOLDEN PLATED STEEL BASKET WITH GOLDEN TERMINAL

GOLDEN PLATED BUMPED & VENTED STRUCTURE

2 INCH KAPTON VOICE COIL

60 + 60 OZ MAGNET STRUCTURE

GOLDEN INJECTED POLYPROPYLENE CONE

WIDE NON-FATIGUING RUBBER SUSPENSION

1000 WATTS MAX, 500 WATTS RMS

Click to read more...

 

[ramos 5,000+ posts]

I will be more than happy to tell ya. But I need to know the impedence of the subs. //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[hyhat33]

It doesn't say unless this helps don't know what these abbreveations are for

* Fs: 43.1

* Qms: 6,24

* Qes: 0.53

* Qts: 0.49

* SPL: 89.8 dB

* Vas: 1.483 Cubic Ft.

thanx!

 

[Wonderbread 5,000+ posts]

just tell us waht model your subs and amp are...

those numbers ahve to do with the speakers producing sound, such as excusrsion, cone area, etc...

what modelsa re they doth?

 

[hyhat33]

The 2 speakers are

PYRAMID IMPERIAL SERIES

1000 WATT 10 INCH GOLD SUBWOOFER

MODEL PW10290

The amp is a

SOUNDSTORM RAVE SERIES

1600 WATT 2 CHANNEL AMPLIFIER M

ODEL R8002

Thanx!!!

 

[Wonderbread 5,000+ posts]

ok, with those woofers, you will be able to obtain eitehr a 4 ohm stereo load, by hooking each woofer up to a channel, or a 2 ohm load, bridged...

too bad taht amp cant handle a 2 ohm load...

how much are you paying for this amp?

 

[hogger 5,000+ posts]

When it says 4 ohm max when it is talking about bridged, it is talking about the speakers, so he could either run four ohm stereo or two ohm mono, because if it could handle 2ohms x 2, it could handle 4 ohms briged, which would also be a 2 ohmn load. Know what I mean?

 

[Wonderbread 5,000+ posts]

i tihnk you are wrong..

the amp can only su[pport a final load presented to it of 2 ohms in stereo (2 cahnnels) or 4 ohms bridged (together into one channel)

each Sub has a single 4 ohm voice coil...

you could achieve either a 2 ohm load, if he were to wire them together into parallel, or a 4 ohm stereo load, if he were to wire each sub directly to the amp...

See what I'M saying?

 

[blackgeltabs 5,000+ posts]

Ok bub this is the deal, your subs are svc 4ohm, look into the soudstrom Rave R350.4 this is 700x2 @4ohm's. Should work a little better than the other one. or look into a JBL 600.1 its right around that price range, and it would be just as good if not better.

 

[Wonderbread 5,000+ posts]

taht's what i was getting at...

i did ask how much he was paying for taht amp.... i was going to suggest teh JBL 600.1

 

[blackgeltabs 5,000+ posts]

Im figuring he was looking at http://www.justamps.com and I think the amp was like 155 so the JBL is like 25-30 bux more. And is probably 10-20x more efficcient:evil:

 

[Wonderbread 5,000+ posts]

yup yup,. 180 or so for the JBL... IkeSound, free shipping....

go with teh JBL, it will blow those subs b4 it blows itself...

just watch your gains, i dont know how much those subs can really take...