THE Thread

I have a convertable its cloth top same as his camaro, but Im think a re sx 15, but I cant decide man with the mag be louder then the re sx 15? I dont know lol just cant decide got till the end of august.

 
it would be sweet is somebody had an install that would get their soft top to bounce.

I can make my soft top sunroof open by itself in my convertible tracker //content.invisioncic.com/y282845/emoticons/satan.gif.9c6a335ed7aeeed3ee273e573f1fcaac.gif It's not that hard at all. crank it up real loud and the top looks like it starts breathing or some $hit. The problem lies in keeping the pressure inside. Really hard to do in a rag top. //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 
Let me tell ya a quick story about the hillbilly's in my new neighborhood. //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif A friend came over to have me take a look at his system in his car. Everything kept cutting in and out on him. ( fuse holder under the hood was loose ) As we were finishing up and listening, one of my new neighbors approached us. Started chit chatting with the guy, he seemed pretty cool. He asked if I could take a look at the amp he just installed in his truck. He said it would work for a little while. But the wiring got so hot, it was glowing red. He said he didn't have that problem with his smaller amp he installed a couple of months before. He said he would buy my friend an I a sixer for our troubles. Me being the stand up red blooded american male I am, couldn't pass up free beer. //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif So I said sure man, bring your truck on up here. About 5 minutes later he was back with his truck. Which by the way, is a freakin' awesome a$$ 04' Lightning. After I got done wiping the drool from my chin //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif I asked him to show me the wiring. So he proceeds to climb up under the truck. Well I got down on the ground so he could show me his fine work. He drilled about a 2" hole in the floorboard of the truck behind the drivers seat to pass the wire through. No grommet, silicone or anything just a wide open hole. But it get's better, the only wire I see going into this hole is a little black wire that was no more than 14-16 ga. So I asked him where was the power wire for this amp. He said that's the power wire feeding both of them :O I told him that was his problem. If he would like I would go ahead and rewire them for him with the proper gauge wire. He asked how much it would cost. I told him I would do it for nothing, I allready had the wire. And I would hate to see such a beautiful truck burn to ashes. He said he would sure appreciate it, and we could think of some way for him to repay the favor. So he popped the hood. And I climbed up under the hood to start taking the wire loose. I d@mn near pissed my pants when I looked under the hood. There was a house (120v ) 100amp circut breaker duct taped to the side of the battery //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif After a few stifled chuckles, I proceeded to unwrap the 4000' of electrical tape wrapped around the wire //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif Nothing could prepare me for what I saw next. The little 14-16 ga. wire I had seen earlier was nothing more than a coat hanger with electrical tape wrapped around it. :eek: :thumbsup //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif//content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 
here's a picture of my newest head unit

z4.jpg


 
Activity
No one is currently typing a reply...

About this thread

RangerMan

Premium Member
Premium Member
Thread starter
RangerMan
Joined
Location
NC
Start date
Participants
Who Replied
Replies
182,982
Views
3,250,561
Last reply date
Last reply from
x2o
IMG_0710.png

michigan born

    May 14, 2026
  • 0
  • 0
IMG_0709.png

michigan born

    May 14, 2026
  • 0
  • 0

New threads

Top