(2) TangBand W69-1042
http://www.tb-speaker.com/detail/1208_03/w69-1042.htm
i did drill two small holes in each so that i could use the stock mounting holes in my rear deck.
i can get pics of this if you'd like, but they don't affect performance at all.
Profile AP1040
http://www.crutchfield.com/S-K7jzreY3v0T/cgi-bin/ProdView.asp?g=120&I=489AP1040
# Peak Output Power (4 Ohms): 150W x 4
# RMS Output Power (4 Ohms): 75W x 4
# Peak Output Power (2 Ohms): 250W x 4
# RMS Output Power (2 Ohms): 125W x 4
# Bridged RMS Output Power (4 Ohms): 225W x 2
# MOSFET Power Supply : Yes
# Total Harmonic Distortion:
# Signal / Noise Ratio: 103 dB
# High/Low Level Converter (Male RCA): Yes (Dual)
# Pre-Amp (RCA) Outputs: Yes
# Variable Treble Boost at 8kHz 0-12 dB (CH 1&2)
# Variable Bass Boost at 45Hz 0-12 dB
# 12dB/Octave Crossover (High Pass/Full/Low Pass) HP/Full/LP
# Variable LP Crossover Frequency: 50 - 250 Hz
# Variable HP Crossover Frequency: 80 Hz -1.2 kHz
# Fuses: 2 x 30A
# Dimensions:
# (2" H x 10 1/4" D) 13 1/16" W
# Power/Speaker Terminal Size (Gauge): 4 / 6
here's the story on this stuff:
i was having sub/amp problems and my car's electrical wasn't liking me, so i decided to give this setup a try.
subs in rear deck for simplicity, and 4ch amp to power the whole system (coaxials in doors and subwoofer's bridged to the other two channels).
the amp will power these subs perfectly (and leave two channels free).
BUT now that Ascendant Audio is coming out with new subs, i've decided to give them a shot (as well as buy a new alternator //content.invisioncic.com/y282845/emoticons/crap.gif.7f4dd41e3e9b23fbd170a1ee6f65cecc.gif), so i'd like to get rid of these items.
other than the two small hoes i drilled in the tangbands, these items are in like new condition.
i had them installed for one weekend and probably have less than an hour of play time!
amp: $90 shipped
subs: $80 shipped
please PM me with any other offers/questions. thanks!
http://www.tb-speaker.com/detail/1208_03/w69-1042.htm
i did drill two small holes in each so that i could use the stock mounting holes in my rear deck.
i can get pics of this if you'd like, but they don't affect performance at all.
Profile AP1040
http://www.crutchfield.com/S-K7jzreY3v0T/cgi-bin/ProdView.asp?g=120&I=489AP1040
# Peak Output Power (4 Ohms): 150W x 4
# RMS Output Power (4 Ohms): 75W x 4
# Peak Output Power (2 Ohms): 250W x 4
# RMS Output Power (2 Ohms): 125W x 4
# Bridged RMS Output Power (4 Ohms): 225W x 2
# MOSFET Power Supply : Yes
# Total Harmonic Distortion:
# Signal / Noise Ratio: 103 dB
# High/Low Level Converter (Male RCA): Yes (Dual)
# Pre-Amp (RCA) Outputs: Yes
# Variable Treble Boost at 8kHz 0-12 dB (CH 1&2)
# Variable Bass Boost at 45Hz 0-12 dB
# 12dB/Octave Crossover (High Pass/Full/Low Pass) HP/Full/LP
# Variable LP Crossover Frequency: 50 - 250 Hz
# Variable HP Crossover Frequency: 80 Hz -1.2 kHz
# Fuses: 2 x 30A
# Dimensions:
# (2" H x 10 1/4" D) 13 1/16" W
# Power/Speaker Terminal Size (Gauge): 4 / 6
here's the story on this stuff:
i was having sub/amp problems and my car's electrical wasn't liking me, so i decided to give this setup a try.
subs in rear deck for simplicity, and 4ch amp to power the whole system (coaxials in doors and subwoofer's bridged to the other two channels).
the amp will power these subs perfectly (and leave two channels free).
BUT now that Ascendant Audio is coming out with new subs, i've decided to give them a shot (as well as buy a new alternator //content.invisioncic.com/y282845/emoticons/crap.gif.7f4dd41e3e9b23fbd170a1ee6f65cecc.gif), so i'd like to get rid of these items.
other than the two small hoes i drilled in the tangbands, these items are in like new condition.
i had them installed for one weekend and probably have less than an hour of play time!
amp: $90 shipped
subs: $80 shipped
please PM me with any other offers/questions. thanks!
