table saw tips?

[PV Audio 5,000+ posts]

got my table saw working and it ain't bad at all. only problem is that i am having a wee bit of trouble keeping the board aligned with the fence. any general tips on the saw or specifically how to saw large boards? thanks

//content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

Click to read more...

 

[JimJ 5,000+ posts]

Use rollers or build an external table so you can keep the board level to the blade.

 

[DBfan187 5,000+ posts]

C-clamp the fence in place?

 

[PV Audio 5,000+ posts]

it has this like clamp thing already on it. it slides down the table and u push down on this lil cam and it locks it into place

 

[Moe Lester 10+ year member]

just go slow, dont try and tear through it. apply force slightly towards the fence like in the pic. also, dont cut a piece wider than it is long. It will tend to wobble alot more and can be dangerous. once that blade grabs hold of it when wobbling, its gonna end up either in your stomach or several feet behind you.

for large boards, do what jack said.

 

[audiolife 5,000+ posts]

and practice with some small scraps. be safe most of all be comfortable but not too comfortable ..respect it dont fear it lol

 

[vettelovr1124 10+ year member]

It will tend to wobble alot more and can be dangerous. once that blade grabs hold of it when wobbling, its gonna end up either in your stomach or several feet behind you..

I've done that before in shop class...still have the scar on my forearm. 'Tis a bad thing to do.

 

[kuijo 10+ year member]

Use push sticks for any small peices of wood.

 

[analogkid]

i usually clamp a straight edge to the mdf and make 1 or 2 cuts with a circular saw so the pieces are workable on the tablesaw.

 

[req 5,000+ posts]

lol, get somone to help you.

ripping 4'x8' sheets is next to impossible by yourself, unless you have TABLE saw, not a dinky bench saw //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 

[PV Audio 5,000+ posts]

yeah i figured out that it was easier to just use the circular saw to get it nice and workable, then cut the baffles with the saw. still ned to get 'er level tho (my garage slopes towards the middle for a drain, so the ground isn't level).

 

[PV Audio 5,000+ posts]

nice....

 

[req 5,000+ posts]

Any bets on how long it'll take lemans to lose a digit ?

three days. //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

i got $5 on this bet.

 

[saywhat? 5,000+ posts]

if u have ur front back and sides, cut them ALL AT ONCE! u will NEVER get the same 13.5 inch or whatever everytime. u will never be exact 100% of the time. if u are 2 mm short, CUTE EVERY PIECE that should be that length if possible. cut a 48 inch piece at say 13.5 that way, u can come back and cut it at the length u need, and all ur pieces are the EXACT same height.

 

[Buckshot 10+ year member]

if u have ur front back and sides, cut them ALL AT ONCE! u will NEVER get the same 13.5 inch or whatever everytime. u will never be exact 100% of the time. if u are 2 mm short, CUTE EVERY PIECE that should be that length if possible. cut a 48 inch piece at say 13.5 that way, u can come back and cut it at the length u need, and all ur pieces are the EXACT same height.

Now thats a **** good tip! If you can make that work, I would!