For Those With Honda Civic

[FlyBri]

Black '99 Civic EX Coupe

Head Unit: Pioneer DEH-P940MP

Component Speakers: Diamond Audio HEX S600a

Rear Speakers: Diamond Audio M391i 6x9's (not yet installed)

Speaker Amp: Audiobahn A8002T 200x2 Watts RMS @4 Ohm

Sub Amp: Visonik V900XD Class X/D Mono Amp

Sub: One 15" Orion H2 in sealed box wired @ 2 Ohm for 1000 Watts RMS of thump

 

[Intercooler 10+ year member]

Black '99 Civic EX Coupe



Head Unit: Pioneer DEH-P940MP

Component Speakers: Diamond Audio HEX S600a

Rear Speakers: Diamond Audio M391i 6x9's (not yet installed)

Speaker Amp: Audiobahn A8002T 200x2 Watts RMS @4 Ohm

Sub Amp: Visonik V900XD Class X/D Mono Amp

Sub: One 15" Orion H2 in sealed box wired @ 2 Ohm for 1000 Watts RMS of thump

How was it getting the Hex's in the doors? Did you use spacers?

 

[JLCivic 10+ year member]

Can those that responded send or post some pictures? Just wondering how everyone made out mounting components in the doors. I have a 98 Civic in progress but only have a Pioneer head unit so far.

Pictures of my setup are on my SD page listed in my sig.

 

[ryan570 10+ year member]

What size components fit in the doors? I have a 98 civic. I was thinking about getting the re components (6.5") but i dont think that will fit

 

[johnecon2001 5,000+ posts]

Those will fit but you have to becareful about the depth of the speaker. The holes are not deep at all. You may have to hack away a bit to get them to fit.

 

[slick316 10+ year member]

here are some pics of what i started to do in my trunk, going to be a while before its done though (over a month for sure, time constaints): http://slickssite.com/install/

 

[Shugarra 10+ year member]

95 Civic EX-R

Rockford Fosgate 8250ti

RS-Audio Tec 6.5" components

Magnum d2

Zapco 360 (bridged for components)

Crossfire BMF 1000d for sub

2 cubic foot box tuned to 29hz

 

[johnecon2001 5,000+ posts]

Didnt know there was such a thing as an "EX-R". We making up trim lines now?

 

[ighettoboyi 10+ year member]

^^ lol i love it when people do that

 

[JimJ 5,000+ posts]

The "R" adds 5hp.

 

[johnecon2001 5,000+ posts]

The "R" adds 5hp.

lmao, nah thats at least a 25 horse gain. lol

to the wheels!

 

[JimJ 5,000+ posts]

Oh, OK...I think I was forgetting that you need to have a Kanji symbol by the "R" to get the real added power //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif

 

[1zenlunatic 10+ year member]

Ive got a 90 civic 4 dr with 6 1/2" crystal csc60s components in the doors.

speaker depth allowance is 1 3/4" in this honda.

These components require a 2 1/2" mounting depth.

Therefore a 1" spacer was made ( I measured the depth allowance wrong the first time!~)

I'm making a 3/4" spacer now.

To install the wiring, you can either drill through the molex plug (very carefully) and thread the wires through the stock housing into the cabin of the vehicle

OR drill a hole in the actual door right next to the molex plug. Slip a rubber grommett on the hole, thread your speaker wires through, and thread through rubber housing on the exterior portion (where wires travel from door to cabin. Cut into the stock housing and thread your wire the rest of the way through there. Silicone the wire/grommett juncture for better seal.

The easiest way to make the spacer hole is to use a hole saw bit on a drill. Use a jigsaw for the outer shape.