OK, To start off with,
I have 2 DD 1508's. $150+ shipping each S4 coil. 2 on the far right, non CF cones.
2 Infinity 1211a. $150+ shipping each Great amps. I had them pushing my 2 RL-p 18"s.
SPECIFICATIONS:
mono subwoofer car amplifier
854 watts RMS x 1 at 4 ohms (1300 watts RMS x 1 at 2 ohms)
variable low-pass filter (32-320 Hz @ 12 dB/octave)
Dynamic Bass Optimization (DBO) circuit (0-12 dB @ 20-80 Hz)
Class D design
CEA-2006 compliant
preamp inputs and outputs
fuse rating: 40A x 3
4-gauge power and ground leads recommended ? wiring and hardware not included with amplifier
19-3/8"W x 2-11/16"H x 12-1/8"D
Planet Audio BB175.4B 350x4. NOT WORKING Not to sure what is wrong with it. It keeps coming in & out of protection. Because I have to put a price $1000, but $$Make me an offer$$Bottom amp
1 Kicker 10" Comp. $1000 but $$Make me an offer$$
I'll get pix later
RF 301.X 4ch. Pix up later $1000 $$Make me an offer$$
Multi Channels
Bridgeable
RMS Power at 4 Ohms 40 W x 4
RMS Power at 2 Ohms 72 W x 4
Performance
Frequency Response 20 Hz - 20000 Hz
Signal to Noise Ratio 100 dB
THD at Rated RMS Power 0.05 %
Crossover / Equalizer
Bass Boost Without Bass Boost
Low - Pass Frequency 80 Hz - 120 Hz
High - Pass Frequency 80 Hz - 120 Hz
Other Features
Input Voltage 14.4 volt
MOSFET Circuitry Yes
3 Way Ready Yes
Dimensions
Width 12.07 in.
Depth 9.85 in.
Height 2.38 in.
An older Kenwood KAC-628 2CH. Good little amp to push some mids or tweeters. $1000 Make an offer$$ Pix up later
2 Kenwood 10" kfc-w2502 S4 ohm. They both work and sound good, but one does have a hole in the plastic cone $1000 Make an offer Pix up later.
//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif
I have 2 DD 1508's. $150+ shipping each S4 coil. 2 on the far right, non CF cones.
2 Infinity 1211a. $150+ shipping each Great amps. I had them pushing my 2 RL-p 18"s.
SPECIFICATIONS:
mono subwoofer car amplifier
854 watts RMS x 1 at 4 ohms (1300 watts RMS x 1 at 2 ohms)
variable low-pass filter (32-320 Hz @ 12 dB/octave)
Dynamic Bass Optimization (DBO) circuit (0-12 dB @ 20-80 Hz)
Class D design
CEA-2006 compliant
preamp inputs and outputs
fuse rating: 40A x 3
4-gauge power and ground leads recommended ? wiring and hardware not included with amplifier
19-3/8"W x 2-11/16"H x 12-1/8"D
Planet Audio BB175.4B 350x4. NOT WORKING Not to sure what is wrong with it. It keeps coming in & out of protection. Because I have to put a price $1000, but $$Make me an offer$$Bottom amp
1 Kicker 10" Comp. $1000 but $$Make me an offer$$
I'll get pix later
RF 301.X 4ch. Pix up later $1000 $$Make me an offer$$
Multi Channels
Bridgeable
RMS Power at 4 Ohms 40 W x 4
RMS Power at 2 Ohms 72 W x 4
Performance
Frequency Response 20 Hz - 20000 Hz
Signal to Noise Ratio 100 dB
THD at Rated RMS Power 0.05 %
Crossover / Equalizer
Bass Boost Without Bass Boost
Low - Pass Frequency 80 Hz - 120 Hz
High - Pass Frequency 80 Hz - 120 Hz
Other Features
Input Voltage 14.4 volt
MOSFET Circuitry Yes
3 Way Ready Yes
Dimensions
Width 12.07 in.
Depth 9.85 in.
Height 2.38 in.
An older Kenwood KAC-628 2CH. Good little amp to push some mids or tweeters. $1000 Make an offer$$ Pix up later
2 Kenwood 10" kfc-w2502 S4 ohm. They both work and sound good, but one does have a hole in the plastic cone $1000 Make an offer Pix up later.
//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif
