Banda Viking 5k

Status
Not open for further replies.

adrum96

Member
Rating: 0%
0 0 0
Item(s) for Sale:

Banda Viking 5000

Item(s) Description/Condition:

Straight From Banda's Website

1 Ohm Stable (nominal)

5000w 1 ohm / 12.6v

3600w 2 ohm / 12.6v

6700w 1 ohm / 14.4v

4300w 2 ohm / 14.4v

Class of Operation: Class D Full Bridge

Frequency Response: 25Hz to 8kHz

LED Clipping Indicator on the Amp

Average Musical Current Draw: 400A

Protection Circuitry:

Reverse Supply Polarity

Output Short Circuit

Supply Voltage Limit:

> 12v (Recommended)

> 10v (High potential for damage under 10.0v)

Dimensions: 17-11/16 x 10-5/8 x 2-3/8

9/10 for cosmetic because the amp does have slight damage on the mounting feet from being mounted. There are also small scratches on the amp just from use. Originally bought locally from adulbrich and has never been ran below 12.6v. I am also including a RCA 2 female to 1 male splitter because the amp only accepts one RCA input, and I won;t be needing it anymore.

Price:

$650.00 Shipped to the Lower 48

Shipping and Miscellaneous Item Information:

Included

Item Pictures:

View attachment 26552390

View attachment 26552391

View attachment 26552392

View attachment 26552393

View attachment 26552394

(List pictures in this section, 1st picture should be your username/date if you have less than 10 positive feedbacks with the i-Trader system or less than 10 references that you have sold to in the past. (These must be listed in your signature, or a link provided to a feedback thread listing these references)).

 
Last edited by a moderator:
Just keep the 5k and use it on your next setup, lol.
Turn the gain down and be easy on the volume knob //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif
Yea over 5k rms to a single 10? I'll tell you how that goes haha

 
Ok. What was issues people said taramps had ? Was it to much voltage kills them or something I don't remember. Are they temperamental ? I'm looking for a nice amp to replace my current one. If I'm wording this wrong I apologize in advance.

 
I'll just run it at 8 ohms haha
Yea, can do that too

Ok. What was issues people said taramps had ? Was it to much voltage kills them or something I don't remember. Are they temperamental ? I'm looking for a nice amp to replace my current one. If I'm wording this wrong I apologize in advance.
Don't give them over 15.5v

also don't mount them to a box without vibration-dampening. They have one large power supply, instead of many smaller coils. This makes them more likely to rattle off the board.

I ran this amp at 15v no problem. Highest it saw was 15.2v.

Zero issues and a solid amp

 
The only thing you really can't do with these amps is run them below 1 ohm. If you're at 1 ohm and keep the voltage above 12.6v (which isn't hard with this amp) it will perform perfectly.

 
Status
Not open for further replies.
Activity
No one is currently typing a reply...

About this thread

adrum96

Member
Thread starter
adrum96
Joined
Location
Springfield, IL
Start date
Participants
Who Replied
Replies
50
Views
8,833
Last reply date
Last reply from
adrum96
IMG_20260516_193114554_HDR.jpg

sherbanater

    May 16, 2026
  • 0
  • 0
IMG_20260516_192955471_HDR.jpg

sherbanater

    May 16, 2026
  • 0
  • 0

New threads

Top