Aq Dustcap Punched In - Easy fix?? *PIC*

[TnT_Sounds 10+ year member]

I think Jb would absord into the cap would it not?

Shouldn't...

It's versatily for many things.. Wal-Mart sells some JB Weld for clothing and alike uses.

 

[allout13 10+ year member]

x2 with the suction cup. maybe use a little glue on the bottom of the cup (something that will clean up) let the glue dry and then pop that sucker out

 

[TNTR70 10+ year member]

use your penis pump

seriously though. very tiny drop of super glue then put the end of some fishing line to that, make sure it is in the center of the dented area, pull slightly then . snip of with razor blade or small wire cutters

 

[WOT]

I ****ed it up even more today, wouldnt pull, si i drilled a 1/16" hole and tried to pull it up with a tiny allen key.

Didnt "pop" back into form, and it just looks uglier.

Dj is sending me a new one. I'll just glue it overtop

Oh well

 

[JL Audio 5,000+ posts]

push a stick through the pole. or something along those lines from behind.

this is what i did to a pair of ap/spls and it worked fine.

 

[James Bang 5,000+ posts]

Theres no obstructions from the bottom underneath? I did already install the subs, and really dont have access to the back anymore.........

too fucking lazy to uninstall?

 

[grimreper912003 5,000+ posts]

I ****ed it up even more today, wouldnt pull, si i drilled a 1/16" hole and tried to pull it up with a tiny allen key.
Didnt "pop" back into form, and it just looks uglier.

Dj is sending me a new one. I'll just glue it overtop

Oh well

Cut it off. Dont just go over top.

 

[Notloud00 10+ year member]

too fucking lazy to uninstall?

u cant push it from the back tard.

 

[Xprime4 10+ year member]

any vids of your wall yet WOT? you still running sd2.5 ? the cones look like the one on the hdc3

 

[WOT]

Cut it off. Dont just go over top.

Oh yeah Ill cut the old one for sure. No I wasnt to lazy to pull the subs, they werent even fully installed, only 2 screws in each, I was told you couldn't push through the back anyways

And xprime, no vids of the wall, I just built and put it in yesterday and made all the templates and beauty pieces fit PERFECT. Finished the neat wiring idea I came up with today. It is 4 15" SDC 2.5's though. No power for them yet, waiting on my amp to get back from repair (tuesday) for the substage, and a pair of selenium st350 supertweeters and kicker amp also form repair. Itll be running within the week though, then Ill get some vids and see it my electrical can handle this amp this time

 

[ThatChevyGuy 5,000+ posts]

I would stronly advise against gluing the new dustcap on top of the old one. Properly remove the old one, clean the surface, then reglue the new one.

 

[James Bang 5,000+ posts]

u cant push it from the back tard.

oh freakin' well. it would've help w/ pics of the rear

 

[WOT]

Ya I didnt have any pics of the back of the subs and couldnt find any, didnt notice the cap when I was wiring, just noticed when I mounted it

 

[dbeez 5,000+ posts]

That happened to one of my nightshades I just cranked the volume up testing and it popped back out after a bit...

 

[DumpinTreos 10+ year member]

I've popped mine out two ways through the vent pole through the back of a sub and played some music and it magically popped back out.l