Recent content by kerpit

3 sets of massive audio ck6 then a ported sa10 off a soundqubed amp. Just being in a boat i have to have them cranked so loud to hear them when i'm swimming. So the loudest i can get is preferred. I think i'll wire up a pair at 4 ohm and then a pair at 2 ohm to see if i can hear any audible...

thanks for the help...i'm searching the site like crazy now too. I did think about doing the 4 ohm/2 ohm thing and just turn the gain down on the 2 ohm set to match. I'm not really missing mid bass. Just before i wired this boat up i was wondering if i should change how i've always had it...

This is in a boat. I'm not too concerned with losing stereo. I have 3 sets, so 6 speakers which is making it difficult! And i don't want to cut holes for another pair! The way i have had it wired before is by using three channels. Each set (2 speakers) wired in parallel to achieve a 2 ohm load...

I am seeking help on deciding how to wire my component speakers. I have 3 sets of 4 ohm 6.5 components and was planning on wiring each set in parallel to a single channel. So i would use only 3 channels and they would each be running at 2 ohms each. Is there a sound difference or can the dsc...

gotcha, i built the box @ 1.25 net per dc's recommendation.

Hi There I need some advice on a sub decision. Earlier this spring i built a 1.25 net ported enclosure for a dc level 3 12" sub for my boat. I putzed around and had no idea it would take 2-3 weeks to have it built. I needed a sub for a trip so i ended up building a reducer plate on the face of...

I was originally going to put the Dayton in my boat but ended up choosing a dc level 3 due to the low sensitivity. I was afraid it wasn't going to be loud enough. I run 3 sets of ck6 components @ 200 rms that get pretty loud. My current port is 7.5 tall 2 wide and 22.5 long. Parts express told...

Checking out the lms-r specs right now! What do you think eta would be on a custom sub from psi?

I'd like to stay with a 12 if possible because I cut the **** hole already!!! Lol. Would a sundown sa12 just sound horrible in that small of a box if ran on 1k watts?

Thank you for the recommendation. I realized i probably should have mentioned my box is only 8.25 deep.

I built a box that is 1.25 cu ft tuned to 32 hz for my boat. I specifically built it for a dc level 3 12 sub. I did not know that with shipping it was going to take over 3 weeks for dc to build the sub. I have a trip planned may 14th and want a sub for this box! I'm searching for a used dc level...

Hi There I have been researching on how to design a slot ported box. I'm having trouble figuring out exactly what size I should build the port. I'm putting a single dc level 3 12 in a 1.25 cu ft net box tuned at 35 hz per dc. Due to the size of the cabinet I'm placing the sub in my boat the...

I'm only looking at subs with rubber surrounds for the moisture/uv reasons. My alpine type r lasted 10 years in the last boat. Took it apart last night and the aluminum cage was corroded. Bead blasted/paints and she's back in business! I still want something new and better than that old type r...

No magician! The storage compartment door is a rectangle that is 9" wide. The compartment itself is huge, just a small width door. So I built a .7 cubic foot box that is 14x14x9 and once the box was in the compartment I installed the sub in the box. I'm most likely going to have to do that again...

Hi There I am seeking help on a subwoofer setup recommendation for my boat. I currently have an alpine type r 1242d sub in a sealed .85 enclosure that is ancient and the aluminum is rotting from the elements in the boat over the years. Anyhow I'm looking to start over. The storage compartment...