Recent content by Jstevens0716

Well i toyed around with it a little today, and i was unable to find any sort of setting for subwoofer lvl besides the on/off. I pulled the subs out of the box to check to see how they were wired. Am i wired 1 Ohm? I have my subs in a center ported box, terminals on each side of the box...

Well i will definitly try this in the morning. I do have the lpf/hpf crossover settings, and then the sub On/Off... But i havent found the sub lvl yet. Ill have to give it a shot. It keep you guys posted. Im sure its something stupid like missing a setting somewhere, these alpine HU are not...

Thats been a huge question on mine, but i havent found a sub adjustment, just an on/off. I downloaded the manual, but it doesnt say anything about sub adjustments. just lpf/hpf, sub on/off

Yes, the HU subwoofer option is on. By turning up the lpf, got me to my correct voltage that i was looking for, but im still having an issue with output. I am not getting much output from the woofers at all... My electrical is staying right at 14.7 volts, all my connections are clean and tight...

. Oh ok, no kidding. I didnt know that. I just opened it up to approx. 80hz

Yes, running 1 ohm. Goal of 50v =2500rms

Ok guys, quick update. I just got back in from the garage. Now correct me if im wrong, but when you are setting input voltage, you turn everything to flat/0 right? I have hpf/lpf on headunit flat with volume at 25 (0-35 max), all my amplifier settings at flat/0, bass knob plugged into amp...

Ok, cool. Well ima run out to the garage now and see what happens. I also just looked up my head unit, and from the info iv gathered it has 4v preouts, so i should be setting that switch on the amplifier to 2v-8v?

I previously was running a Soundstream VIR-8300NR, but someone i had spoke with on this forum said that may have been my issue. So i swapped out my VIR-8300NR with an older alpine i had laying around that i pull out of my last car before i sold it.... HU= Alpine CDA-9830

Sorry for confusion, I turned lpf all the way down only to set the gain. I previously had to it to approx. 80hz on the amp and same on HU. And still not getting much output. Prior to the system, i was running a SS Rubi 1.2500 and a Sundown Nightshade 15, in my old tiburon and running a...

Ok, Thanks man. Im literally making the adjustments as we speak. How do i know/find out what my preout V is? Yes, the switch on my amp is .1v-2v/2v-8v. Previously i had set the switch to 2v-8v, but i am trying to reach 49-50 volts, for the 2500 rms rating, but at 2v-8v i can only adjust the...

lol Hey Guys, I know my title sounds very noob'ish, but i do have a couple questions for ya guys. I recently purchased a Soundstream Rubicon 1.2500 Amplifier, and iv had some difficulties getting this amp adjusted. I set amplifier input voltage, but i was getting very little output from...

Set lpf to 80hz on the amplifier and hu? I was having a.problem before with my door speakers getting to much bass, the stock speakers couldnt hack it. I had set to hpf 80hz to help...

That may very well be an option in the near future, but honestly i am really hoping to work out my tuning issue with some fellow caraudio members to make my current amplifier work. After speaking with many people, the information i have gathered is that the amplifier isnt the problem, its the...

So since i have put up this thread i have recieved sone helpful information in response to my question, and also via PM. I have done some extensive research since posting this, and came to a conclusion that there are many of you guys on here running this Soundstream Rubicon 1.2500 amplifier...