Recent content by Audio freak

OK guys awesome. I can't wait to get the q1 2200.1 I just purchased it. I'll update on how it is once I get it.

Ok Ive narrowed it down to q1 2200.1 bc2000d ampere audio 2000.1 and scv 1500d or if I save more scv 2000d. I personally am interested in the q1 2200.1 because I found one used in great condition and I have heard nothing but good about them. How is the q1 2200.1? I'm gonna get it more than...

Someone clamped it in comparison up against some big amps and it did some pretty good numbers but its only an SPL test and not a dyno run with certified or uncertified. Its been a pressed issue to get one on a dyno lol. Looking for Q1-2200D Dyno - Page 3 - D'Amore Engineering - High Quality Car...

Pm'd I can do 285 and pay for fastest shipping you can do as well. I have paypal.

Thanks for that link that's an awesome bargain. Had some great dyno results. Even though it is cheaper it will give me time to save up for something crazy expensive in the future if something happens but this amp seems pretty well built.

I found a few options like the bc2000d and soundqubed 2200.1 and sundown audio scv 1500.1 which would suite me well with the 15v capped supply for better power at 12v. Any one know of where I could find these amps or similar ones around 1500-2000 watts rms used? I found a few 2200.1 in the...

Thanks for the replys. I'm definitely gonna see what I can do as far as 0 gauge big three and maybe a run the back because I really would like to future proof myself. Its just such a small area on the firewall so i may need to deal with the 4 gauge for a while. Problems with the kicker is I have...

I'm looking for any suggestions on an amplifier for a single sundown audio X-15. It is currently being ran off of a kicker cx1200.1 at 1ohm. Basically it's not 1ohm stable and it's had the living crap beat it at 1ohm for a few years. It's not doing to we'll and I'm looking for an amp that will...

After experiencing the quality of what CSCstang built for the single SA 12 I had to have him build an enclosure for the X-15 I have had lying around for a while. It is a birch wood enclosure 4.5 cubic feet and tuned to 28hz with a double layer baffle. Also had him stain the enclosure and it came...

I ordered a custom built enclosure to specifications for a single SA 12" and I have to say it is absolutely amazing. I've always had pefabs and never expected a single 12" to do what this does. The overall frequency response is phenomenal and can go real low and hit real hard in the upper 30hz...

Anyone with a Ford Taurus be very careful. Some of the wires in the harness behind the Headunit look like the twisted speaker outputs but are not. I can not find a single bit of info on these new Taurus sel models. I'm bugging service departments right now. If I can get a diagram or something...

I've gone through hell and back taking the Headunit out and I'll say it was a nightmare. Now I'm trying to find what the color coding of the main wiring harness behind the myford touch Headunit is. I already found the obvious 12v red trigger wire I'll be using for rem to amp. But I can't find...

I'm looking to get as loud and clean as I can without going all out SPL with the tahoe I have. I don't want a wall (yet) because I don't feel the need to tear it into Peices until I have gotten good use out of the vehicle. Anyways I'm struggling for money due to bills and have a few subs left...

Yeah I'm thinking of keeping the X-15 to mess with inside and put the 2 XFL in my tahoe. May even get 2 more eventually and do 4 XFL 12"s but not yet. Gotta get a custom enclosure for the first 2. Anyways those XFL POUND because in my old car they not only would flex windows in stores when I was...

BTW that CX1200.1 at 1ohm pounds. I set it with a Oscilloscope and those 2 xfl 12"s even in that prefab where ground pounders. Barely would get warm after a hour or so of playing and would shake windows of stores. Also broke one of my rear windows off the regulator motor in old car I used to...