WTT - 3HP+ W/Tall Gap for 3HP+ W/Short Gap

[ciaonzo 5,000+ posts]

I have a 3HP+ with the tall collar (35mm top plate) and I need a 3HP+ with the 12mm top plate and provisions for the male half of the QCA ring. I don't need the actual ring. My motor also has a copper lining on the T-yoke for low inductance. If you think you might be interested in trading, please let me know. Thanks.

Click to read more...

 

[ciaonzo 5,000+ posts]

While we're on the topic of an LMS 4000, I would very much like to have a mint 15" top assembly with a high roll surround. //content.invisioncic.com/y282845/emoticons/naughty.gif.94359f346c0f1259df8038d60b41863e.gif A guy can dream, can't he?

 

[ciaonzo 5,000+ posts]

Up for Sunday.

 

[terra 5,000+ posts]

No love for the 3hp+? Great motor, if I had anything I'd trade you. Or perhaps you'd be interested in a set of steel parts?

 

[ciaonzo 5,000+ posts]

No love for the 3hp+? Great motor, if I had anything I'd trade you. Or perhaps you'd be interested in a set of steel parts?

Thanks, Alex. Yeah, I definitely need to grab those plates from you at some point. I priced out the amount of NEO I would need and it's stratospheric. Will have to wait a bit on it since I need some winter tires.

 

[terra 5,000+ posts]

I've got some neo I could include..probably a couple thousand percent cheaper too haha.

 

[ciaonzo 5,000+ posts]

I was looking to get about five or six pre-charged cylinders measuring 1" x 2". I think I can save a bit by going with N42 since it will be an underhung setup and heat won't be a concern. Have any of those?

 

[terra 5,000+ posts]

No, all I have is the pie slices I showed in the pics. But I seriously doubt you can assemble the cylinders post charge...

 

[ciaonzo 5,000+ posts]

No, all I have is the pie slices I showed in the pics. But I seriously doubt you can assemble the cylinders post charge...

I'll be building a jig that resembles the thing that holds poker chips and gluing them in one at a time. A different jig for the top plate will include a cylinder the exact width of the gap and something to help me lower the top plate down slowly and systematically without my fingers being anywhere near the assembly. That's the plan anyway. I've done similar things before plus I've got quite a bit of practice handling charged NEO from building ribbons. You're right though, it's pretty risky. Are you able to charge NEO?

 

[terra 5,000+ posts]

Me personally? no. Let me know if you need anything I've got though. Good luck with the trade!

 

[ciaonzo 5,000+ posts]

Me personally? no. Let me know if you need anything I've got though. Good luck with the trade!

Thanks very much, Alex. I'll be in touch. //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif

 

[ciaonzo 5,000+ posts]

Help meh.

 

[grimreper912003 5,000+ posts]

WTT: TC9 w/ .75" slug for TC9 w/ 1" slug

Oh, wrong thread //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif greedy.

Any reason your changing, or did you have the wrong version all along? I remember you saying your set. Don't mean to be nosey, just curious //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif.

 

[ciaonzo 5,000+ posts]

WTT: TC9 w/ .75" slug for TC9 w/ 1" slug
Oh, wrong thread //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif greedy.

Any reason your changing, or did you have the wrong version all along? I remember you saying your set. Don't mean to be nosey, just curious //content.invisioncic.com/y282845/emoticons/smile.gif.1ebc41e1811405b213edfc4622c41e27.gif.

Haha...//content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif

No, I just got this one through an awesome trade deal but I need the other version. I guess if I can't get one, I'll use this for something else or sell it. Not sure.

 

[maintrain 10+ year member]

dude... you know I need this! You know my dilemma!

nevermind, I need the same one you are trying to trade for.