WTB: Small 2 channel amp

[basscort2009 5,000+ posts]

Product I'm looking for:

 

a small 2 channel amp. wouldnt mind something oldschool if it worked perfect. newschool is more than fine also

 

Budget:

 

100 or less please

 

Condition:

 

like new, mint, very good

 

Time Frame (if applicable):

asap

Click to read more...

 

[CHEMMINS 10+ year member]

Small physically or small power?

 

[infamous_e46 5,000+ posts]

coustic 240se 28 shipped

needs repair

 

[basscort2009 5,000+ posts]

power. need about 50x2. but i also dont need a 2 ft long 2 channel either lol.

 

[BlactimusCrime 10+ year member]

orion xtr250, 100 shipped

 

[basscort2009 5,000+ posts]

pics? specs?

 

[infamous_e46 5,000+ posts]

Image Hosting at TurboImageHost.com

240SE 400SE 600SE

Rated Power @ 14.4 V (0.1 % THD): 2 x 60 Watts 2 x 100 Watts 2 x 150 Watts

4 Ohm Stereo

Rated Power @ 14.4 V (0.1 % THD): 2 x 120 Watts 2 x 200 Watts 2 x 300 Watts

2 Ohm Stereo

Rated Power @ 14.4 V (0.2 % THD): 1 x 240 Watts 1 x 400 Watts 1 x 600 Watts

4 Ohm Mono

Frequency Response: 20 –20,000 Hz 20 –20,000 Hz 20 –20,000 Hz

+/- 0.5 dB +/- 0.5 dB +/- 0.5 dB

Input Sensitivity: 0.1 – 5 V 0.1 – 5 V 0.1 – 5 V

S/N Ratio @ rated power: 100 dB 100 dB 100 dB

High-Pass Filter Crossover Frequency: 30 - 300 Hz 30 - 300 Hz 30 - 300 Hz

(Continuously Variable, @18 dB/Oct.)

Low-Pass Filter Crossover Frequency: 30 - 300 Hz 30 - 300 Hz 30 - 300 Hz

(Continuously Variable, @18 dB/Oct.)

Bass Boost Level: 0 - 18 dB @ 45 Hz 0 - 18 dB @ 45 Hz 0 - 18 dB @ 45 Hz

Dimensions: 11" W (280 mm) 11" W (280 mm) 11" W (280 mm)

2 3/8" H (60 mm) 2 3/8" H (60 mm) 2 3/8" H (60 mm)

8 1/2" L (215 mm) 13 3/16 L (335 mm) 15 1/2 L (395 mm)

SPEAKER IMPEDANCE

Although extremely low impedance speaker loads will not damage the amplifier, for stereo mode,

we recommend speaker loads of 2, 4 or 8 ohms; for bridged mono mode, 4 or 8 ohms. (Note: In

bridged mono mode, the amplifier sees only half of the speaker impedance.)

NOTE remember that we are not defying the laws of Physics! IF you decide to connect ANY

Coustic amplifier into a bridged mono load BELOW 4 ohms, Physics dictates that current draw

doubles! This is not too big a problem with the 240SE or 400SE. But with the 600SE this is

DANGEROUS. The current draw could be as great as 200 amps (peak). Make sure you wire

your system properly.

With the 600SE we recommend ONLY a 4 gauge wire OR larger

http://www.coustic.com/support/pdfs/Coustic240.400.600.SEManual.pdf

 

[basscort2009 5,000+ posts]

no thanks jose //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

 

[BlactimusCrime 10+ year member]

http://www.caraudio.com/forums/amplifier-classifieds/510048-xtr-250-2150-a.html

 

[basscort2009 5,000+ posts]

pming now.

 

[infamous_e46 5,000+ posts]

Uploaded with ImageShack.us

?????

 

[basscort2009 5,000+ posts]

Uploaded with ImageShack.us

?????

more than 100 i bet //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

 

[infamous_e46 5,000+ posts]

more than 100 i bet //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif

i was cold i traded for a few logs and a lighter

 

[basscort2009 5,000+ posts]

lol

 

[morespl 10+ year member]

i have this fosgate 225.2 http://www.caraudio.com/forums/amplifier-classifieds/514452-old-school-usa-rocford-fosgate-225-2-a.html