WTB 4 channel amp kit

[CrimsonNCream]

Looking to buy a new 4 channel amp kit. Speakers 100 watts rms 200 watts peak. Been out the game for a LONG time so don't know exactly what I'm looking for. My current amp will be underpowering them temporarily while I look for an amp that gives them full power so I'm still looking for a kit that will handle the full power.

Click to read more...

 

[trumpet 5,000+ posts]

The size of power wire you need depends on the amplifier, not the speakers. Since it's better to go bigger than you need right now you should have 4 AWG at minimum. I use this size wire for power and ground the most. I could give you a deal on this kit plus another 2-channel RCA, or I can get you a 4-channel RCA to simplify the wiring.

T-Spec V10-4RAK Premium 4 AWG Oxygen Free Copper Amplifier Installation Kit | Easy Way Electronics

 

[mylows10 5,000+ posts]

Where are you located. I have kits as well

 

[CrimsonNCream]

In Colorado

 

[CrimsonNCream]

The size of power wire you need depends on the amplifier, not the speakers. Since it's better to go bigger than you need right now you should have 4 AWG at minimum. I use this size wire for power and ground the most. I could give you a deal on this kit plus another 2-channel RCA, or I can get you a 4-channel RCA to simplify the wiring.T-Spec V10-4RAK Premium 4 AWG Oxygen Free Copper Amplifier Installation Kit | Easy Way Electronics

I did know that much. That's why I want a kit that will have enough power for a bigger amp since I'm going to upgrade the amp and I don't want to buy another kit after this one.

 

[mylows10 5,000+ posts]

What you need is a 0 gauge kit then if you plan in getting a sub amp a well then you can go off the distro block for power and ground for that amp. The only wire you'll need to run is a third RCA from the back of the deck and a remote jumper from the existing amp I have the kits in stock as well What you need to figure out is. How big of a sub amp you'll be running , this will dictate either a cca amp kit or the ofc kits and possibly a big 3 kit as well

 

[CrimsonNCream]

Well if I do run a sub I have a first gen Orion 250 HCCA with one channel broken and the bridging module for it. Even with one channel broken that might be enough because IF I run subs I'm planning on something that hits and gets low (hopefully) but not very loud in terms of watts. I am also looking into getting the HCCA repaired if need be.

 

[mylows10 5,000+ posts]

Nice amp

 

[CrimsonNCream]

What you need is a 0 gauge kit then if you plan in getting a sub amp a well then you can go off the distro block for power and ground for that amp. The only wire you'll need to run is a third RCA from the back of the deck and a remote jumper from the existing amp I have the kits in stock as well What you need to figure out is. How big of a sub amp you'll be running , this will dictate either a cca amp kit or the ofc kits and possibly a big 3 kit as well

Nice amp

Thanks. So what kind of kit would you recommend for a four channel amp (MTX Blue Thunder 504) lower watt SQ sub (on the 250 HCCA) and how much $ would it be?

 

[mylows10 5,000+ posts]

A cca 0 g kit $110 with the distro block and 3 rcas

 

[CrimsonNCream]

A cca 0 g kit $110 with the distro block and 3 rcas

What does CCA mean?

That may well be the going rate but at $110 I may just try to pull the existing wiring out of my old ride.

 

[mylows10 5,000+ posts]

Copper clad aluminum if you going to be using 2 amps. You need the wire to handle to power load. And need to be able to split to power to both amps any decent or good kit with a distro block and 3 sets of rcas will cost this or more

 

[mylows10 5,000+ posts]

http://www.caraudio.com/forums/electrical-wiring-classifieds/571430-wire-amp-kits-big-3-kits-sale.html