ls2poweredgoat
5,000+ posts
Womanizer
So, as you guys know from seeing my other thread, I FINALLY ordered a pair of ID OEM's from HessDawg (great guy BTW). I created a thread (link below) and took a few pictures of just ONE of the mids, while the other chilled in the box.
So I took the other mid out of the packaging, took both out in the garage, took one of my door panels off, wire some shit up, grab the mid and notice the frame is bent to shit. Luckily it was just the lip, and the actual basket wasn't damaged at all. Now the shipping box wasn't very beat up at all, and the mids are packaged decently enough.
So I carefully put the ***** in the vice and straightened it out the best I could, again, luckily its bent where one of the four screw holes are, so I'm hoping when I screw it in after I make some new baffles, it will straighten the frame out even more.
I'm livid right now, not only because of that, but I destroyed one of my baffles trying to get it out because the motor on the OEM is so large it fits in my stock speaker hole with about 1/8" clearance all around it.
//content.invisioncic.com/y282845/emoticons/furious.gif.fc81ca146dbff91fede3ed290dbc4f4c.gif//content.invisioncic.com/y282845/emoticons/verymad.gif.3f39c5c2fd57527b671fad3efdfac756.gif//content.invisioncic.com/y282845/emoticons/furious.gif.fc81ca146dbff91fede3ed290dbc4f4c.gif//content.invisioncic.com/y282845/emoticons/verymad.gif.3f39c5c2fd57527b671fad3efdfac756.gif//content.invisioncic.com/y282845/emoticons/furious.gif.fc81ca146dbff91fede3ed290dbc4f4c.gif//content.invisioncic.com/y282845/emoticons/verymad.gif.3f39c5c2fd57527b671fad3efdfac756.gif//content.invisioncic.com/y282845/emoticons/furious.gif.fc81ca146dbff91fede3ed290dbc4f4c.gif
I honestly just think the box was dropped on its side, if they didn't come damaged from the factory.
I would take some pics, but that mid is currently in the car, and it sounds pretty good so far.
http://www.caraudio.com/forum/showthread.php?t=363463
So I took the other mid out of the packaging, took both out in the garage, took one of my door panels off, wire some shit up, grab the mid and notice the frame is bent to shit. Luckily it was just the lip, and the actual basket wasn't damaged at all. Now the shipping box wasn't very beat up at all, and the mids are packaged decently enough.
So I carefully put the ***** in the vice and straightened it out the best I could, again, luckily its bent where one of the four screw holes are, so I'm hoping when I screw it in after I make some new baffles, it will straighten the frame out even more.
I'm livid right now, not only because of that, but I destroyed one of my baffles trying to get it out because the motor on the OEM is so large it fits in my stock speaker hole with about 1/8" clearance all around it.
//content.invisioncic.com/y282845/emoticons/furious.gif.fc81ca146dbff91fede3ed290dbc4f4c.gif//content.invisioncic.com/y282845/emoticons/verymad.gif.3f39c5c2fd57527b671fad3efdfac756.gif//content.invisioncic.com/y282845/emoticons/furious.gif.fc81ca146dbff91fede3ed290dbc4f4c.gif//content.invisioncic.com/y282845/emoticons/verymad.gif.3f39c5c2fd57527b671fad3efdfac756.gif//content.invisioncic.com/y282845/emoticons/furious.gif.fc81ca146dbff91fede3ed290dbc4f4c.gif//content.invisioncic.com/y282845/emoticons/verymad.gif.3f39c5c2fd57527b671fad3efdfac756.gif//content.invisioncic.com/y282845/emoticons/furious.gif.fc81ca146dbff91fede3ed290dbc4f4c.gif
I honestly just think the box was dropped on its side, if they didn't come damaged from the factory.
I would take some pics, but that mid is currently in the car, and it sounds pretty good so far.
http://www.caraudio.com/forum/showthread.php?t=363463
