So I benched my RD D9....

groundpound4200
5,000+ posts

Da fuq did I just read?
free air and I'm still rising to almost 3 ohms from .5 //content.invisioncic.com/y282845/emoticons/verymad.gif.3f39c5c2fd57527b671fad3efdfac756.gif How is that possible. I was going to post on CACO under the RD section but its gone //content.invisioncic.com/y282845/emoticons/crazy.gif.c13912c32de98515d3142759a824dae7.gif//content.invisioncic.com/y282845/emoticons/laugh.gif.48439b2acf2cfca21620f01e7f77d1e4.gif

So is it normal to have that kind of impedance rise with no box or is my meter fuxored //content.invisioncic.com/y282845/emoticons/confused.gif.e820e0216602db4765798ac39d28caa9.gif

Vid is uploading...

 
No box.... this is a free air test. The meter on the left is hard to see, sorry guys. At 50 hz I was getting just under 75VAC. I went up 2 clicks on the volume and gained 20V on the last couple burps

 
I benched 4824w out of my D9 starting at .5 and rising to 1.02ohms. I don't know exact battery voltage but it wasn't too good... started at 14.1 and dropped to somewhere around 12. I was pretty impressed with that number with low voltage.

It seems to really come alive when you keep the load down (under 1 ohm)as long as its not low enough to make protection kick in (much under .5 and it gets protect happy)

 
I benched 4824w out of my D9 starting at .5 and rising to 1.02ohms. I don't know exact battery voltage but it wasn't too good... started at 14.1 and dropped to somewhere around 12. I was pretty impressed with that number with low voltage.

It seems to really come alive when you keep the load down (under 1 ohm)as long as its not low enough to make protection kick in (much under .5 and it gets protect happy)

 
I benched 4824w out of my D9 starting at .5 and rising to 1.02ohms. I don't know exact battery voltage but it wasn't too good... started at 14.1 and dropped to somewhere around 12. I was pretty impressed with that number with low voltage.

It seems to really come alive when you keep the load down (under 1 ohm)as long as its not low enough to make protection kick in (much under .5 and it gets protect happy)

 
I benched 4824w out of my D9 starting at .5 and rising to 1.02ohms. I don't know exact battery voltage but it wasn't too good... started at 14.1 and dropped to somewhere around 12. I was pretty impressed with that number with low voltage.

It seems to really come alive when you keep the load down (under 1 ohm)as long as its not low enough to make protection kick in (much under .5 and it gets protect happy)

 
I benched 4824w out of my D9 starting at .5 and rising to 1.02ohms. I don't know exact battery voltage but it wasn't too good... started at 14.1 and dropped to somewhere around 12. I was pretty impressed with that number with low voltage.

It seems to really come alive when you keep the load down (under 1 ohm)as long as its not low enough to make protection kick in (much under .5 and it gets protect happy)

 
I benched 4824w out of my D9 starting at .5 and rising to 1.02ohms. I don't know exact battery voltage but it wasn't too good... started at 14.1 and dropped to somewhere around 12. I was pretty impressed with that number with low voltage.

It seems to really come alive when you keep the load down (under 1 ohm)as long as its not low enough to make protection kick in (much under .5 and it gets protect happy)

 
I benched 4824w out of my D9 starting at .5 and rising to 1.02ohms. I don't know exact battery voltage but it wasn't too good... started at 14.1 and dropped to somewhere around 12. I was pretty impressed with that number with low voltage.

It seems to really come alive when you keep the load down (under 1 ohm)as long as its not low enough to make protection kick in (much under .5 and it gets protect happy)

 
Activity
No one is currently typing a reply...
Old Thread: Please note, there have been no replies in this thread for over 3 years!
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.

About this thread

groundpound4200

5,000+ posts
Da fuq did I just read?
Thread starter
groundpound4200
Joined
Location
Mankato, MN
Start date
Participants
Who Replied
Replies
30
Views
2,274
Last reply date
Last reply from
andrew2944r
IMG_1882.jpeg

slater

    Oct 4, 2025
  • 0
  • 0
Screenshot_20251004_120904_Photo Translator.jpg

1aespinoza

    Oct 4, 2025
  • 0
  • 0

New threads

Top