SOLD
Just as title States Have a Rockford Fosgate Power T10001BD Amp for sale.
Was in my wifes 2009 Mustang for about 8 months...we are trading her car in on a 2011 mustang (ordering it) so i took the system out today just to get everything straight before we take it down to get it appraised at the dealer. Amp works 100% had it on a pair of 12" Kicker cvrs and they sounded great.
I would say the amp cosmectically is a 8 or 9 outta 10 a few little scratches nothing major unless you up close (im very picky)
I have tons of refs on here....some are in signature i know there are more.
Amp will be shipped via UPS and insured.
Asking $275 OBO email me at rschwerma76@yahoo.com for fastest response or pm me here:
May consider trades depending on what it is...im looking for a good indash for my truck
As you know these amps are unrated....
Specs:
# 1000 Watt RMS Class BD Amplifier
# RMS Power Ratings:
* 500 watts RMS x 1 at 4 ohms
* 750 watts RMS x 1 at 2 ohms
* 1,000 watts RMS x 1 at 1 ohm
# Para-Punch bass EQ (0-18 dB with variable center frequency between 35-70 Hz) with wired remote control
# MEHSA- High Performance Thermal management design for bigger power with more consistent thermal stabiity
# MOSFET power supplies and outputs
# TOPAZ - Circuit for eliminating engine noise
# NOMAD - Advanced short circuit and power protection
# MasterSync - allows one amplifier to manipulate another amplifier's gain, EQ, Infrasonic and crossover controls
# PowerSync - Allows bd series amplifiers to be "strapped" together to create one massive power combination
# variable low-pass filter (32-250 Hz, 24 dB/octave)
# Infrasonic filter: 12dB/oct Butterworth alignment protects the amp from unwanted ulta-low frequency information, increasing the usable power output and reliability
# RCA Preamp Outputs
# Phase switch: 0 - 180 degrees
# Cast aluminium heatsinks - allows more power into a smaller heatsink be allowing engineers to localize heat in specific areas
# 3-Stage Variable forced convection - heatsink design that keeps the amp's internal comonents cool
# 1/0 AWG power and ground connections with internal ANL fusing
# Dimensions: 18" L x 12.8" W x 2.66" H
# CEA-2006 Compliant
Just as title States Have a Rockford Fosgate Power T10001BD Amp for sale.
Was in my wifes 2009 Mustang for about 8 months...we are trading her car in on a 2011 mustang (ordering it) so i took the system out today just to get everything straight before we take it down to get it appraised at the dealer. Amp works 100% had it on a pair of 12" Kicker cvrs and they sounded great.
I would say the amp cosmectically is a 8 or 9 outta 10 a few little scratches nothing major unless you up close (im very picky)
I have tons of refs on here....some are in signature i know there are more.
Amp will be shipped via UPS and insured.
Asking $275 OBO email me at rschwerma76@yahoo.com for fastest response or pm me here:
May consider trades depending on what it is...im looking for a good indash for my truck
As you know these amps are unrated....
Specs:
# 1000 Watt RMS Class BD Amplifier
# RMS Power Ratings:
* 500 watts RMS x 1 at 4 ohms
* 750 watts RMS x 1 at 2 ohms
* 1,000 watts RMS x 1 at 1 ohm
# Para-Punch bass EQ (0-18 dB with variable center frequency between 35-70 Hz) with wired remote control
# MEHSA- High Performance Thermal management design for bigger power with more consistent thermal stabiity
# MOSFET power supplies and outputs
# TOPAZ - Circuit for eliminating engine noise
# NOMAD - Advanced short circuit and power protection
# MasterSync - allows one amplifier to manipulate another amplifier's gain, EQ, Infrasonic and crossover controls
# PowerSync - Allows bd series amplifiers to be "strapped" together to create one massive power combination
# variable low-pass filter (32-250 Hz, 24 dB/octave)
# Infrasonic filter: 12dB/oct Butterworth alignment protects the amp from unwanted ulta-low frequency information, increasing the usable power output and reliability
# RCA Preamp Outputs
# Phase switch: 0 - 180 degrees
# Cast aluminium heatsinks - allows more power into a smaller heatsink be allowing engineers to localize heat in specific areas
# 3-Stage Variable forced convection - heatsink design that keeps the amp's internal comonents cool
# 1/0 AWG power and ground connections with internal ANL fusing
# Dimensions: 18" L x 12.8" W x 2.66" H
# CEA-2006 Compliant
Last edited by a moderator:
