KnuKoncepts KLMX 1/0

[duece212 5,000+ posts]

if you have any tight bends to make or just want ease of running the cable get the fleks. I've had both and the klm is some non flexible stuff, it gets you there if your down on money and have straight runs to make.

 

[Racerx250 10+ year member]

Just get kicker hyperflex. It's 0/1 is closer to 0/2 and its STOFC and more flexible than anything out imo.

 

[duece212 5,000+ posts]

Just get kicker hyperflex. It's 0/1 is closer to 0/2 and its STOFC and more flexible than anything out imo.

knu flex be the same stuff

 

[ultimate157 5,000+ posts]

Just get kicker hyperflex. It's 0/1 is closer to 0/2 and its STOFC and more flexible than anything out imo.

1/0 2/0 3/0 4/0

 

[Bun-Bun 10+ year member]

Overrated? Most of the time. I've used low strand welding 1/0, uberflex welding wire, Hyperflex, Schoshe, etc... I much prefer to work with the Hyperflex over any other of those wires because its like running a thick rope through your vehicle.
There were a few places in my Jeep that required the flexibility of Hyperflex to make the bend.

x2 I wouldn't have been able to make the run to my starter without the fleks...

Now the cable under there car... thats a different story. Could have used cheaper cable but meh //content.invisioncic.com/y282845/emoticons/cool.gif.3bcaf8f141236c00f8044d07150e34f7.gif

 

[DBDRAGGUY 10+ year member]

knu flex be the same stuff

Exactly the same cable.

 

[Black Truck 10 10+ year member]

Im just gonna get the Fleks to be safe. I would rather pay more for the fleks, than spend money on the KLMX and it maybe not work. If it does eh, itll at least be a learning experience as ive never worked with 1/0 wire before!

 

[duece212 5,000+ posts]

Im just gonna get the Fleks to be safe. I would rather pay more for the fleks, than spend money on the KLMX and it maybe not work. If it does eh, itll at least be a learning experience as ive never worked with 1/0 wire before!

You'll dig the cable, ultra flexible and just **** nice to work with in general.

 

[helotaxi 5,000+ posts]

If I was running cable every day, I might like the extra flexibility, but, seriously? The difference when running it once every couple years hardly justifies the difference in price.

 

[Black Truck 10 10+ year member]

ya I agree

 

[ultimate157 5,000+ posts]

If I was running cable every day, I might like the extra flexibility, but, seriously? The difference when running it once every couple years hardly justifies the difference in price.

Most people get it just to say they have flexible wire.

Where I needed the flexibility, the wire made a 90* bend from the floor, up ~3 or 4" and then a 180* bend back down. This is where the rear seats are in the Grand Cherokee.

 

[iamamp3pimp 5,000+ posts]

The KLMX is supposed to be much more flexible than the KLM was and uber flexibility is highly overrated.

THANK YOU

i was gonna say about the dude that can wrap his fleks cable tightly around 2 fingers........AND, that doesnt mean anything,

you can do the same with a coat hanger

 

[iamamp3pimp 5,000+ posts]

and welding cable.

 

[ultimate157 5,000+ posts]

you can do the same with a coat hanger

And if you keep forcing wire to bend like that, all you're doing is stressing the material.

 

[iamamp3pimp 5,000+ posts]

once its in place, its all good.