Crossfire CFA30HC $135 shipped!

Status
Not open for further replies.

Goindef154
5,000+ posts

Nothing
Rating: 100%
23 0 0
Item(s) for Sale:

Old School Crossfire CFA30HC

Item(s) Description/Condition:

I'd give it an honest 7/10 it's not great but I cleaned it up real nice and it's in pretty good shape for the age, also because of the new marks thanks to the back of my seat.

I have heard that though it states 640 @ 1 ohm it does closer to 1000 but obviously I don't have the equipment to prove that.

Specs(Thanks to LoudCivic):

CFA30HC

Power 4 ohms .008%THD: 15 watts x 2 30 watts x 2

RMS Power 4 ohms@0.02%THD*: High Power- 60 watts x 2

High Current- 35watts x 2

High Power- 120 watts x 2

High Current- 65watts x 2

RMS Power 2 ohms@0.02%THD *: High Power- 110 watts x 2

High Current- 60watts x 2

High Power- 210 watts x 2

High Current- 120watts x 2

RMS Power 1ohm@0.02%THD *: High Power- 185watts x 2

High Current- 110watts x 2

High Power- 320watts x 2

High Current- 210watts x 2

RMS Power .5 ohm@0.02%THD *: High Current- 185watts x 2 High Current- 320watts x 2

Maximum RMS Bridged Mono

0.02%THD:

High Power- 370 x 1 @ 2ohm

High Current- 370 x 1 @ 1ohm

High Power- 640 x 1 @ 2ohm

High Current- 640 x 1 @ 1ohm

Bandwidth: 11Hz – 38Khz 11Hz – 38Khz

Selectable 12dB Crossover: LP/FULL/HP Variable 45 – 150Hz LP/FULL/HP Variable 45 – 150Hz

RCA Preout: Yes Yes

Bass Boost: Variable: 0 to+12 dB @ 45Hz Variable: 0 to+12 dB @ 45Hz

Signal to Noise: >100dB >100dB

Channel Separation: >70dB >70dB

Input Sensitivity: 340mv to 5.2 volts 340mv to 5.2 volts

Input Impedance: 20K ohms 20K ohms

Damping Factor: >400 >480

Dimensions: 9.6”W x 2.0”H x 13”L 9.6”W x 2.0”H x 18.5”L

Price:

$135 shipped and insured

Shipping and Miscellaneous Item Information:

Item Pictures:

DSC05707.jpg


DSC05708.jpg


DSC05709.jpg


DSC05710.jpg


DSC05784.jpg


DSC05787.jpg


(List pictures in this section, 1st picture should be your username/date if you have less than 10 positive feedbacks with the i-Trader system or less than 10 references that you have sold to in the past. (These must be listed in your signature, or a link provided to a feedback thread listing these references)).

 
If the top was not so ruff I would pick it up, but the install I have in mind needs to clean for the owner.

bump for a nice amp though.

As for the fusing, it has been a while since I messed with these. IIRC the bottom fuses are actually supposed to be for output fusing.

 
Status
Not open for further replies.
Activity
No one is currently typing a reply...

About this thread

Goindef154

5,000+ posts
Nothing
Thread starter
Goindef154
Joined
Location
Phoenix, AZ
Start date
Participants
Who Replied
Replies
27
Views
2,723
Last reply date
Last reply from
Goindef154
IMG_0710.png

michigan born

    May 14, 2026
  • 0
  • 0
IMG_0709.png

michigan born

    May 14, 2026
  • 0
  • 0

New threads

Top