12" Sundown Z v2

[ThumpinTitan 10+ year member]

1. Product:

12" Sundown Zv2 SPL

2. Specs:

Nightshade Cone

Nightshade v1 Coil

Nightshade Spider (Single)

Dual 1 ohm

3. Description/Condition:

Few light scratches on Motor and Basket... Sub is in like new condition

Jacob recommends this sub for SPL use as the nightshade coil is very tight in the gap and can rub on music. Ive been runnin it daily off a Mojo 2k in a 1.75cu ft @ 34

I cannot guarantee it wont rub on you its worked pretty well for me. Was really only played to and from work (30 minutes each way) for about a month at not even half volume

Will be shipped in Original Sundown Box/Packaging.

4. Price:

$175 + Shipping

14" x 14" x 14" @ 57lbs from 92026

5. Pictures:

(List pictures in this section, 1st picture should be your username/date if you have less than 10 positive feedbacks with the i-Trader system or less than 10 references that you have sold to in the past. (These must be listed in your signature, or a link provided to a feedback thread listing these references)).

Click to read more...

 

[southport2014 10+ year member]

so as of now there is no problems with it correct and whats the rms and what can it really handle pm me best priced shipped to 46237 thabks

 

[ThumpinTitan 10+ year member]

Right now the sub plays exactly as i got it fro Jacob. Its played fine for me, but jacob says it may rub and strongly suggests this is an SPL sub

if you push down on the cone it doesnt rub, unless u push slightly sideways and down (im sure most subs rub if you do this anyways)

pm sent with shipping costs

 

[SPLaudio 5,000+ posts]

the sub dose NOT have a nightshade coil. it is not possible and wouldnt fit the gap even with a hammer,lol....

 

[ThumpinTitan 10+ year member]

the sub dose NOT have a nightshade coil. it is not possible and wouldnt fit the gap even with a hammer,lol....

Jacob himself told me it has a nightshade coil... you can ask him if youd like

Its a v1 coil... not the bigger v2 coils

 

[SPLaudio 5,000+ posts]

sorry v1 or v2 nightshade coil dosent fit.

 

[ThumpinTitan 10+ year member]

Alright well im not changing Specs until Jacob comes in and says otherwise

 

[SPLaudio 5,000+ posts]

just dont want someone to buy and not get what they want or expect.

 

[ThumpinTitan 10+ year member]

So peeps dont think im BSing lol

 

[ThumpinTitan 10+ year member]

Bump!!

Will trade for a nice monoblock

 

[J31Rob 5,000+ posts]

lolpwnt

GLWS. Wouldn't mind burping this a couple times.

 

[xmakeafistx 10+ year member]

anticipating @sundownz reply.

 

[nateberrier 10+ year member]

I had me a nice Z v2. Would take 3k easy probably. It now resides in florida //content.invisioncic.com/y282845/emoticons/frown.gif.a3531fa0534503350665a1e957861287.gif Wish I had kept it.

 

[sundownz Pro Seller]

This is one of the only ones we put an NS v.1 coil into -- ONLY the 50mm long NS v.1 coil fits this motor. It's incredibly tight.

NS v.2, Z v.3, NS v.1/2 SPL coils, etc, etc will NOT go in the gap at all.

 

[ThumpinTitan 10+ year member]

There ya go, confirmed by the man himself... Thank you sir!