Recent content by Rsx_03

Thanks for the compliments! I'm a electrical engineer so semi following you, ciaonzo, do you mean microphones on an active inverting operational amplifier fed into my amplifiers to make basically noise cancellation? Problem is noise has to be at an equal amplitude to have cancellation effect...

Freaking awesome post hispls, thanks. Yep lots of options for deadening and I'll need it, I'll research. So narrowing it down for SQ: Sub: 10" sealed rear deck. Currently can get a great great deal on a single shallow typeR for 600rms. I can even do 2x Image Dynamics 10" but would look tacky. ...

Restoring this 67 Camaro Exterior almost complete - need to do hood, trunk, fix a booboo on the back, then paint Mechanics - LS1 engine swap, 4 wheel independent suspension, power brakes/ steering, AC Interior - you can see lol So planning my SQ sound system before paint.  HU - false old...

Its 9/10 condition 100% original Stereo blew out and few speakers started smoking Picked up some Mb quart Pvf 213 Sundown e8v2 d2 Arc Xdi804 Any suggestions on a similar head unit to cda-7949, must play cdr and preferably with an aux in and cd mp3. Needs to be an oldy to keep the factory...

thanks for the suggestions, may have to go with a 4ch amp, 2 front channels to components 2 rear bridged to 8" http://www.arcaudio.com/product-pages/amplifiers/xdi-series/xdi804.asp 8.125"(L) x 6.5"(W) x 2.15"(H) ******* EDIT bought the arc xdi804 Thanks all ^_^

Got a 1992 Porsche 968 it's 100% original until the stereo blew (smoked up some speakers) SUBWOOFER BOX it's going to be in a sealed box like this Subwoofer SUBWOOFER Sundown E8v2 AMP for sub 200 rms amplifier needed, needs to be mounted under dash wired into fuse box I dislike this...

basically i dont run my amps hard at all but i want to add some active cooling (fans) just to prolong there life comes with a plexiglass top 1) where would the hot spots be on this? the large inductor? 2) what size fan? i have all sizes from my PC builds 3) push or pull configuration? 4)...

sweet thanks, took all that in, will do some more research, so far i know that aperiodic looks like a mess to start off with. ported i see people using little 6.5" speakers as subs in all sort of crazy over sized boxes to prove some type of point. sscs6 dont get low enough to play 60hz nicely...

ahhh lol .. thanks for the heads up on the midbass quest so is any sized sealed an improvment of IB? (read lots of mixed reviews, hate an love, .3cu or .4cu) if i take the ported route, cu ft need? port diameter? , i read around on forums that a .6cu ported is good but once i try to calculate...

so disconnected the 4" speakers (makes no difference, probably just a waste of 15 rms and some added weight) turned down the hpf to 80 hz, sounds really nice and got a lot of the midbass i was looking for. next step either: sealed door pods (have to cut my doors and make pods) .25 cu for...

dont have pics but yes, thoroughly deaden doors, aluminum flashing over large holes, then sound raamat on top of it for more support, covered all small holes with raamat over everything put a big sheet of foam. maybe i should get a bigger front amp, i currently have 75rms to each sscs6 and...

ok sealed off doors means sealed boxes for my existing sscs6 ? or sealed off doors means sound deadening? (already used RAAMAT a while, ago) i also put 4" kenwoods powered off the HU with a crossover in the center console (facing horizontally) .. as i expected, didnt do much lol

Current Setup PPI 1000.1 >> JL 12w7 ($50 at local pawn , sorry if it was stolen from you ported at 31hz PPI 300.2 >> Crystal SSCS6 Comps free air Wanting to add more midbass (only midbass, 75hz to 250hz) 2 ohm mono block >> (2) Swiss Audio SAK650 (autobahn sister company...

so far, ppi dcx 300.2 1 components each channel @ 4 ohms - WORKS ! 2 components on 1 channel @ 2 ohms - WORKS ! 2 components on each channel @ 2 ohms - (going to test) i have a ppi dcx 300.2 and a set of crystal sscs6 components. then i bought another pair of sscs6 but dont want to buy...

im doing the same thing. i used to have 1 set of crystal sscs6 (components) + ppi dcx 300.2 amplifier i bought another set of sscs6 components but dont want to buy another amp. so i tested it. i put 2 components on 1 channel (down to 2ohm) and everything seemed fine. ive been playing music...