Recent content by okura_hubby

The lower the ohm load the warmer the amp gets. Some thoughts.. a Coax speaker may not be a 4ohm speaker. Should check it with a multimeter. If it is like 8 or 6.. You could run them series you could get like a 4 or 3 omh load. You should try to avoid using an amp channel to support both full...

Why was the 2300M so expensive, or even made? The amp is basically two 2075M's put into one case. It can not be bridged further, it is only rated at 300W x2 @4Ohm. There is no rating for 2 ohm.. A 2150M was rated 150W x2 @4ohm an 300W x2 @2Ohm, could be bridged and get 600W x1 @ 4ohm. So what...

Ok.. well explain this.. its a black 2150AM... So is it basically just a 2150M with no internal differences...? Precision Power PPI 2150AM Sq Amplifier Old School PPI Quality | eBay

Per PPI website where they keep the manuals.. The stats look same. I am refering to the black 2150AM and the black 2150M Please shed light..

Here is a link to all the PPI manuals on their site.. Has stuff back to late 80's.. Index of /Manuals/Amplifier Manuals Your specific manual you want is here http://www.precisionpower.com/Manuals/Amplifier%20Manuals/Precision_Power_4100AM%20&%204200AM%20Amplifiers.pdf But the official...

Again. Said it twice. Verify the size of the box. Verify what the woofers need. The companies publish their stats on the speakers. Just make the box fit ideal conditions for best results..

I have seen video's of that and it works in improving SPL. Have you calculated the stats of your speaker to see what type of air space they need. Or you just got a box and put the speakers in it? The sealed chamber is to support the speaker to help the speaker respond. If the space is too...

Too many variables to give a black and white answer. 1) what is desired outcome.. Accurate bass, Low bass, SPL? 2) how much space do you have to deal with? 3) certain speakers tend to perform better with one type of enclosure than other types.. Just got to see what the company recommends and...

There is a place on Nimitz.. Right after you get off H1.. Its on the left side heading into Waikiki area. I forget the name.. Might want to goto some of the local cruise in's the Classic Car scene there is HUGE... Google "Paradise Cruisers". They have cruise in-s all the time in the time. I went...

I had them warenteed in 92' before I went to Japan and never used them since.

You have 2 speakers that are dual voice coil. Each coil is a 4 ohm load.. So you in essence have 4 - 4ohm speakers.. As stated in using all coils on all speakers you could end up with one of the following combinations... Option 1: If you connect the + together and - together on one speaker...

I will dig the speakers out of storage. They were never taken out of the box from where I sent the old ones into warentee. I blew some of them up doing an huge Iso box in a Nissan lowrider I will post up what they are. But they were the best that they made in circa 1989-1992..

Looking to make a 3 Chamber, Single Reflex Bandpass Enclosure.. By the diagram, it appears the sealed and the ported chambers are approx size. Is the 2 sealed chambers calculated as sealed? is the shared ported chamber size teh same as the sealed or is it calculated as a ported chamber to a...

As I said I am going to run the subs in separated chambers. So they will not be canceling or competing with air. As long as you separate the woofers so they are in their own environment they will perform the same as if I only had 1..

Not going after SPL.. Putting it in a classic car.. I know they are old school, and they are clean sounding amps.. My plans are this.. I have 4 brand new in the box Lanzer 15" that I had instorage for 24 years. I got Lanzar to warentee them when I headed to Japan in 1991. So my intent is to run...