RCA Wire Interference From Amp Power Wire

[audiobaun 5,000+ posts]

Eddie has a lot of good stuff on his page. Good source for adapters, dash kits, etc too. That's where I get a lot of stuff, he's one of the OG's that's still around.

Installer.com - the #1 installer collaboration platform

The only installation management platform yo'll ever need. Access a network of professional installer companies across categories.

www.installer.com

Installer.com technical and historic papers

Car Audio installation Technical and historic Papers

www.installer.com

Kind of weird. I see the Characters used on his site which I did bookmark. Thanks by the way.. and I am on the TV Pandora station Of Bullet Train Radio listening to Dubstep music with some of the same characters. LOL

 

[EmpiricalApe]

Tucking either the RCAs or Power wiring below the Door seal in the carpet area will be approx 4-8" away from each other and be just fine man. It will be that one location wheer they meet in the Rear if they cross to use a little square foam piece to separate them. Like that Black cell foam at Hdepot or Hobby Lobby in small sheets tape it down or tape around the power or RCAs even. That way you dont have to rip anything out except the old RCAs that you found that were the noise issue you repaired.

Foam Sheet - 12" x 18" | Hobby Lobby | 330415

Make your craft projects standout with this Foam Sheet. This EVA foam sheet features a solid color and is perfect for adding texture and dimension to any poster, scrapbook page, or coloring sheet. The soft material is easy to cut into fun shapes and can be embellished with markers, stickers, and...

www.hobbylobby.com

I guess it was the damaged portion of the rcas.. I Wired a new pair in the same spot and there's no buzz, so I guess I'm all good.

 

[chillin 10+ year member]

How much power are you running? Could you use a distribution block at the end of the 0 for your 8 guage?

 

[EmpiricalApe]

How much power are you running? Could you use a distribution block at the end of the 0 for your 8 guage?

im running 2000 rms on the sub side, I haven't gotten around to running speaker wire for the mids and highs yet, but I'll be running 3-400 rms on for them.

 

[chillin 10+ year member]

With 2500 watts or less, I would think the 0 guage on one side would be good. Split the power at the back to the 2 amps.

 

[audiobaun 5,000+ posts]

im running 2000 rms on the sub side, I haven't gotten around to running speaker wire for the mids and highs yet, but I'll be running 3-400 rms on for them.

Thats a pretty good combination of mids and highs with the sub stage power wise.

 

[EmpiricalApe]

Thats a pretty good combination of mids and highs with the sub stage power wise.

I have a skar vxf 15 on a sundown sfb 3k, Infinity Refrence Series 6.5 Components, Polk Audio 5.25 coaxials for the rear, on a Infinity 3004A. Electrical is a 260amp mechman alt, and xs power d3400, in a 2002 Saturn L200

 

[audiobaun 5,000+ posts]

I have a skar vxf 15 on a sundown sfb 3k, Infinity Refrence Series 6.5 Components, Polk Audio 5.25 coaxials for the rear, on a Infinity 3004A. Electrical is a 260amp mechman alt, and xs power d3400, in a 2002 Saturn L200

Man... That should sound pretty dammned good. NICE!!!

 

[EmpiricalApe]

thank you for the reply, I fixed it a while back..It ended up just being bad rcas. I replaced them and it fixed it.

 

[SlugButter]

I have a skar vxf 15 on a sundown sfb 3k, Infinity Refrence Series 6.5 Components, Polk Audio 5.25 coaxials for the rear, on a Infinity 3004A. Electrical is a 260amp mechman alt, and xs power d3400, in a 2002 Saturn L200

I was just recently playing with the 15 inch VXF and 15 inch ZVX. I can change port tuning on my box to 36 HZ or 25 HZ. ZVX was definitely louder, but the VXF is far better on lows and sounded better. I only have 2k watts on tap for subs. I wish I would’ve put the Skar subs on my Sundown SIA 3500 to see how the 2 subs would take the power.