Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
CarAudio.com Classifieds
Car Audio Wanted
WTB: 4 channel amp
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Pitchblack98" data-source="post: 2792239" data-attributes="member: 569595"><p>Anyone interested in trading (2) 2 channel amps I was going to use. I just dont have room to install both of them so a single 4 channel suits my needs better. One is a Kenwood KAC-729s and the other is a Power Acoustik PA2-1200.</p><p></p><p>Here are the specs...</p><p></p><p>PA2-1200</p><p></p><p>2 Channel</p><p></p><p>2 ohm stable</p><p></p><p>250x2 @ 4 ohm rms</p><p></p><p>300x2 @ 2 ohm rms</p><p></p><p>600x1 @ 2ohm rms</p><p></p><p>1200 peak bridged</p><p></p><p>20.5” x 11.25” x 2.25”</p><p></p><p>KAC-729s</p><p></p><p>2-Ohm Stable</p><p></p><p>Power Indicator</p><p></p><p>Screw-Type Power and Speaker Terminals</p><p></p><p>Speaker Relay Protection</p><p></p><p>Amplifier Type: 2-channel</p><p></p><p>RMS Power @ 4 Ohms: 100W x 2 @ 14.4V</p><p></p><p>THD at 4-Ohm RMS Power: 0.08%</p><p></p><p>Bridged RMS Power @ 4 Ohms: 300W x 1 @ 14.4V</p><p></p><p>Speaker Level Inputs: yes</p><p></p><p>Preamp Outputs: no</p><p></p><p>Built-In Crossovers: HP/LP</p><p></p><p>Bass Boost: 0</p><p></p><p>Frequency Response: 20-20,000 Hz</p><p></p><p>Signal to Noise Ratio: 100 dB</p><p></p><p>Fuse Rating: 2x20 amps</p><p></p><p>Let me know if anyone is interested and I can get some pics for you. That MK800.4 or the memphis amp would work perfect for me. The clarion might be a little small for my needs.</p></blockquote><p></p>
[QUOTE="Pitchblack98, post: 2792239, member: 569595"] Anyone interested in trading (2) 2 channel amps I was going to use. I just dont have room to install both of them so a single 4 channel suits my needs better. One is a Kenwood KAC-729s and the other is a Power Acoustik PA2-1200. Here are the specs... PA2-1200 2 Channel 2 ohm stable 250x2 @ 4 ohm rms 300x2 @ 2 ohm rms 600x1 @ 2ohm rms 1200 peak bridged 20.5” x 11.25” x 2.25” KAC-729s 2-Ohm Stable Power Indicator Screw-Type Power and Speaker Terminals Speaker Relay Protection Amplifier Type: 2-channel RMS Power @ 4 Ohms: 100W x 2 @ 14.4V THD at 4-Ohm RMS Power: 0.08% Bridged RMS Power @ 4 Ohms: 300W x 1 @ 14.4V Speaker Level Inputs: yes Preamp Outputs: no Built-In Crossovers: HP/LP Bass Boost: 0 Frequency Response: 20-20,000 Hz Signal to Noise Ratio: 100 dB Fuse Rating: 2x20 amps Let me know if anyone is interested and I can get some pics for you. That MK800.4 or the memphis amp would work perfect for me. The clarion might be a little small for my needs. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
CarAudio.com Classifieds
Car Audio Wanted
WTB: 4 channel amp
Top
Menu
What's new
Forum list