Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Wiring HELP!
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="papaslack" data-source="post: 8291718" data-attributes="member: 662195"><p>I am looking to wire my 2 channel amp into the max load for two 6.5 speakers.</p><p></p><p>Rockford Fosgate 2.6x</p><p></p><p>(4 ohms)30W x 2 Output Power</p><p></p><p>(2 ohms)60W x 2 Output Power Bridged</p><p></p><p>(Mono)120W x 1 Distortion Max</p><p></p><p>(4 ohms)0.08% Frequency Response</p><p></p><p>(+/- 0.5dB)20Hz - 20kHz Signal to Noise</p><p></p><p>(A-weighted)&gt;100dB Input Sensitivity (+0dB gain overlap)350mV - 6V (low level input)</p><p></p><p>1V - 13V (high level input) Bridgeable Yes Punch EQ</p><p></p><p>(45 Hz / 20 kHz)No Pass-Thru No Xcard Qty 1 Length 7-11/32 in</p><p></p><p>(18.7 cm) Width 8-5/16 in</p><p></p><p>(21.1 cm) Height 2 in</p><p></p><p>I believe i should wire them in series like the below link to drop it to 2ohm. Is this correct?</p><p></p><p><a href="http://www.avsforum.com/photopost/data/2356991/0/0a/0ad54053_sp_wiring_series.gif" target="_blank">http://www.avsforum.com/photopost/data/2356991/0/0a/0ad54053_sp_wiring_series.gif</a></p></blockquote><p></p>
[QUOTE="papaslack, post: 8291718, member: 662195"] I am looking to wire my 2 channel amp into the max load for two 6.5 speakers. Rockford Fosgate 2.6x (4 ohms)30W x 2 Output Power (2 ohms)60W x 2 Output Power Bridged (Mono)120W x 1 Distortion Max (4 ohms)0.08% Frequency Response (+/- 0.5dB)20Hz - 20kHz Signal to Noise (A-weighted)>100dB Input Sensitivity (+0dB gain overlap)350mV - 6V (low level input) 1V - 13V (high level input) Bridgeable Yes Punch EQ (45 Hz / 20 kHz)No Pass-Thru No Xcard Qty 1 Length 7-11/32 in (18.7 cm) Width 8-5/16 in (21.1 cm) Height 2 in I believe i should wire them in series like the below link to drop it to 2ohm. Is this correct? [URL="http://www.avsforum.com/photopost/data/2356991/0/0a/0ad54053_sp_wiring_series.gif"]http://www.avsforum.com/photopost/data/2356991/0/0a/0ad54053_sp_wiring_series.gif[/URL] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Wiring HELP!
Top
Menu
What's new
Forum list
