Reply to thread

Message

<blockquote data-quote="87monteman" data-source="post: 1101205" data-attributes="member: 562931">My amplifier is a Power AcoustiK LT980/2 Hyper Bass Series here are the specs straight from the book.MAX Power @2 ohm 980wRMS @2 ohm 280w x 2CH220 x 2W @ 4ohms RMS280 x 2W @ 2 ohms RMS560 Watts @ Mono RMS980 Watts Bridged MAX PowerTHD @2 ohmSignal/Noise Ratio &amp;gt;98dbChannel Separation &amp;gt;55dbFrequency Response +* 10Hz-30KHz (*plus sighn has an underline in the book)HPF 50Hz-500HzLPF 30Hz-500HzSub Sonic 30HZ-175HZBass EQ 0db-24dbAdjustable Sensitivity Range 0.1-1VInput Impedance - Low Level 10K Ohms2 Ohm Stable StereoTri Mode CapableFuse 15A x 4the amp can handle a minimum impedance of 2 ohms.....it&#039;s two channel i don&#039;t know how to tell if it&#039;s a mono amp but there is a way of wiring it that makes it streo or mono but i can&#039;t understand the book and i have even been trying to do some homework.My subs are Two Power Acoustik 12in. Dual Voice Coil FUBAR series and the Specs are;SPL 91dbMagnet Size 200oz.BASV voice coil: 2&quot;Power (RMS watts): 800Power (MAX watts): 1,800Thiele/Small ParametersFs 36 HzVas 1.91 Cu. Ft.Qms 5.731Qes 0.502Qts 0.462X -max 10mmwell thats about all that i can find. Sorry for not answering sooner but i work strange hours and i really appreciate yall&#039;s help. At the moment i have the subs hooked up on one side (only one voice coil or one side of the speaker) and i&#039;m taking your advice not to bump too loud right now.&nbsp; thanx yall and if i left anything out just lemme know and i&#039;ll happily post it . thanx a bunch and i&#039;ll be checking back soon</blockquote>

[QUOTE="87monteman, post: 1101205, member: 562931"] My amplifier is a Power AcoustiK LT980/2 Hyper Bass Series here are the specs straight from the book. MAX Power @2 ohm 980w RMS @2 ohm 280w x 2CH 220 x 2W @ 4ohms RMS 280 x 2W @ 2 ohms RMS 560 Watts @ Mono RMS 980 Watts Bridged MAX Power THD @2 ohm Signal/Noise Ratio >98db Channel Separation >55db Frequency Response +* 10Hz-30KHz (*plus sighn has an underline in the book) HPF 50Hz-500Hz LPF 30Hz-500Hz Sub Sonic 30HZ-175HZ Bass EQ 0db-24db Adjustable Sensitivity Range 0.1-1V Input Impedance - Low Level 10K Ohms 2 Ohm Stable Stereo Tri Mode Capable Fuse 15A x 4 the amp can handle a minimum impedance of 2 ohms.....it's two channel i don't know how to tell if it's a mono amp but there is a way of wiring it that makes it streo or mono but i can't understand the book and i have even been trying to do some homework. My subs are Two Power Acoustik 12in. Dual Voice Coil FUBAR series and the Specs are; SPL 91db Magnet Size 200oz. BASV voice coil: 2" Power (RMS watts): 800 Power (MAX watts): 1,800 Thiele/Small Parameters Fs 36 Hz Vas 1.91 Cu. Ft. Qms 5.731 Qes 0.502 Qts 0.462 X -max 10mm well thats about all that i can find. Sorry for not answering sooner but i work strange hours and i really appreciate yall's help. At the moment i have the subs hooked up on one side (only one voice coil or one side of the speaker) and i'm taking your advice not to bump too loud right now. thanx yall and if i left anything out just lemme know and i'll happily post it . thanx a bunch and i'll be checking back soon [/QUOTE]

Verification