Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
General Car Audio
What to use to protect wires from heat/melting?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="jeeper2269" data-source="post: 8742460" data-attributes="member: 574943"><p>This is what I am looking at. The black stuff may not work, as I have already run the wires and do Not want to pull them back out. It looks like the other option wraps around. And for appearance, I may see about shooting it with matte black rust oleum stove paint.</p><p></p><p>the wires I am running are going on the top area of the firewall, between the plastic engine cover and the actual firewall. The battery is on the passenger side, about mid bay. So the wires go across to the driver side and down into a hole (conveniently plugged for the clutch that is not there) into the cab.</p><p></p><p>i have one loom for a set of pod lights that go into a switch inside, one loom for a front cam, and one 0 awg amp wire with nylon sheething going inside, through that hole. I ended up modifying the plug by drilling a hole and inserting a grommet. The three wires fit perfect and I was able to simply twist the plug back into place.</p><p></p><p>the other wires ran in the same area are the loom for my power side steps.</p><p></p><p>I plan on running a second 0 awg wire to my other amp in the rear cargo area. This one will be going down the passenger side wheel well (inside, behind the plastic covering) and along the frame.</p><p>This is a Jeep Wrangler, which has several oem wires running in the same areas already</p></blockquote><p></p>
[QUOTE="jeeper2269, post: 8742460, member: 574943"] This is what I am looking at. The black stuff may not work, as I have already run the wires and do Not want to pull them back out. It looks like the other option wraps around. And for appearance, I may see about shooting it with matte black rust oleum stove paint. the wires I am running are going on the top area of the firewall, between the plastic engine cover and the actual firewall. The battery is on the passenger side, about mid bay. So the wires go across to the driver side and down into a hole (conveniently plugged for the clutch that is not there) into the cab. i have one loom for a set of pod lights that go into a switch inside, one loom for a front cam, and one 0 awg amp wire with nylon sheething going inside, through that hole. I ended up modifying the plug by drilling a hole and inserting a grommet. The three wires fit perfect and I was able to simply twist the plug back into place. the other wires ran in the same area are the loom for my power side steps. I plan on running a second 0 awg wire to my other amp in the rear cargo area. This one will be going down the passenger side wheel well (inside, behind the plastic covering) and along the frame. This is a Jeep Wrangler, which has several oem wires running in the same areas already [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
General Car Audio
What to use to protect wires from heat/melting?
Top
Menu
Home
Refresh