Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Builds
Car Audio Build Logs
The bassmachine (the last chapter)
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="2loud4youmorris" data-source="post: 6833658" data-attributes="member: 606814"><p>specs on the subs</p><p></p><p>Specifications: • Power handling: 1,000 watts RMS/4,000 watts peak • VCdia: 4" • Le: 2.8 mH • Impedance: 2 ohms per coil x 2 • Re: 3.02 ohms • Frequency range: 15 - 150 Hz • Fs: 26.5 Hz • SPL: 94.5 dB • Vas: 8.88 cu. ft. • Qms: 6.90 • Qes: 0.25 • Qts: 0.25 • Xmax: 31.0 • Dimensions: Overall diameter 18.52", Cutout diameter 16.83", Depth 11.27" • Weight: 53.4 lbs. Note: All specifications are with voice coils connected in series.</p><p></p><p>High-temperature low eddy-current stainless steel voicecoil former</p><p></p><p>2+2 ohm dual voicecoil 4-layer flatwound Aluminum wire, 4" diameter voicecoil</p><p></p><p>10" linear dual spider suspension with large integral lead-wires</p><p></p><p>3" long segmented radial NdFeB motor assembly, for low mass and very high BL</p><p></p><p>FEA designed 3-roll cloth surround for greater than 2.5" peak-to-peak travel</p><p></p><p>Field-replaceable top assembly system</p><p></p><p>Large anti-flux-modulation shorting ring</p><p></p><p>Sandwich acrylic foam fiberglass cone</p></blockquote><p></p>
[QUOTE="2loud4youmorris, post: 6833658, member: 606814"] specs on the subs Specifications: • Power handling: 1,000 watts RMS/4,000 watts peak • VCdia: 4" • Le: 2.8 mH • Impedance: 2 ohms per coil x 2 • Re: 3.02 ohms • Frequency range: 15 - 150 Hz • Fs: 26.5 Hz • SPL: 94.5 dB • Vas: 8.88 cu. ft. • Qms: 6.90 • Qes: 0.25 • Qts: 0.25 • Xmax: 31.0 • Dimensions: Overall diameter 18.52", Cutout diameter 16.83", Depth 11.27" • Weight: 53.4 lbs. Note: All specifications are with voice coils connected in series. High-temperature low eddy-current stainless steel voicecoil former 2+2 ohm dual voicecoil 4-layer flatwound Aluminum wire, 4" diameter voicecoil 10" linear dual spider suspension with large integral lead-wires 3" long segmented radial NdFeB motor assembly, for low mass and very high BL FEA designed 3-roll cloth surround for greater than 2.5" peak-to-peak travel Field-replaceable top assembly system Large anti-flux-modulation shorting ring Sandwich acrylic foam fiberglass cone [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Builds
Car Audio Build Logs
The bassmachine (the last chapter)
Top
Menu
What's new
Forum list
