Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Subs indoors!
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Jes 42" data-source="post: 7988486" data-attributes="member: 643971"><p><strong>Dayton Audio SPA250 250 Watt Subwoofer Plate Amplifier</strong></p><p></p><p>The Dayton Audio SPA250 subwoofer amplifier produces 250 watts of clean power output, and combines with a host of flexible user options to make it an unbeatable choice. A user-configurable bass boost circuit creates a 6 dB peak at 35 Hz, which allows sealed subwoofer designs and certain ported enclosures to achieve their optimum bass extension and maximum "flat" output.</p><p></p><p>The SPA250 features RCA line level and banana jack speaker level inputs and outputs, automatic power-on that is triggered by any audio input signal, and a phase reverse switch to match the subwoofer to your room and your other speakers. A single amp can accept a stereo input signal and combine it into mono, which is preferred for sub bass reproduction. A preamp or receiver's LFE output may be connected to the SPA250's Left (mono) input. The internal low pass crossover is fully adjustable between 40 and 180 Hz, and of course the amp has built-in protection against internal and external faults.</p><p></p><p>• Variable low-pass filter at 24 dB/octave attenuation from 40 Hz ~ 180 Hz</p><p></p><p>• Switchable phase 0° (NOR) or 180° (REV)</p><p></p><p>• Variable gain MIN/MAX input voltage dependent</p><p></p><p>• Speaker level high-pass outputs 6 dB/octave at approximately 90 Hz @ 4 ohms, 180 Hz @ 8 ohms (i.e. 220 uF electrolytic capacitor)</p><p></p><p>• Line-level full bandwidth (10 Hz- 20 kHz) outputs/throughputs for adding or "daisy chaining" additional amplifiers</p><p></p><p>• Subsonic filter 12 dB/octave high-pass filter centered at 20 Hz</p><p></p><p>• Damping factor at rated power: 114 @ 100 Hz</p><p></p><p><strong>Specifications:</strong> • Measured power output: 156 watts RMS into 8 ohms @ 0.1% THD, 252 watts RMS into 4 ohms @</p><p></p><p>You can get yourself a plate amp like this at Parts Express..Works great on car subs!Only $125.00</p></blockquote><p></p>
[QUOTE="Jes 42, post: 7988486, member: 643971"] [B]Dayton Audio SPA250 250 Watt Subwoofer Plate Amplifier[/B] The Dayton Audio SPA250 subwoofer amplifier produces 250 watts of clean power output, and combines with a host of flexible user options to make it an unbeatable choice. A user-configurable bass boost circuit creates a 6 dB peak at 35 Hz, which allows sealed subwoofer designs and certain ported enclosures to achieve their optimum bass extension and maximum "flat" output. The SPA250 features RCA line level and banana jack speaker level inputs and outputs, automatic power-on that is triggered by any audio input signal, and a phase reverse switch to match the subwoofer to your room and your other speakers. A single amp can accept a stereo input signal and combine it into mono, which is preferred for sub bass reproduction. A preamp or receiver's LFE output may be connected to the SPA250's Left (mono) input. The internal low pass crossover is fully adjustable between 40 and 180 Hz, and of course the amp has built-in protection against internal and external faults. • Variable low-pass filter at 24 dB/octave attenuation from 40 Hz ~ 180 Hz • Switchable phase 0° (NOR) or 180° (REV) • Variable gain MIN/MAX input voltage dependent • Speaker level high-pass outputs 6 dB/octave at approximately 90 Hz @ 4 ohms, 180 Hz @ 8 ohms (i.e. 220 uF electrolytic capacitor) • Line-level full bandwidth (10 Hz- 20 kHz) outputs/throughputs for adding or "daisy chaining" additional amplifiers • Subsonic filter 12 dB/octave high-pass filter centered at 20 Hz • Damping factor at rated power: 114 @ 100 Hz [B]Specifications:[/B] • Measured power output: 156 watts RMS into 8 ohms @ 0.1% THD, 252 watts RMS into 4 ohms @ You can get yourself a plate amp like this at Parts Express..Works great on car subs!Only $125.00 [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Subs indoors!
Top
Menu
What's new
Forum list
