Menu
Forum
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Gallery
New media
New comments
Search media
Members
Registered members
Current visitors
Classifieds Member Feedback
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Register
Forum
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
Log in / Join
What’s new
Search
Search titles and first posts only
Search titles only
Search titles and first posts only
Search titles only
General Car Audio
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Build Logs
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Home Audio
Off-topic Discussion
The Lounge
What's new
Search forums
Menu
Reply to thread
Forum
Car Audio Discussion
Subwoofers
Stupid Question, Easy Answer
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Dynasty" data-source="post: 1784753" data-attributes="member: 567480"><p>This maybe a very stupid question, but is my sub SVC or DVC? I won this on ebay and the seller failed to mention which which one it is. I will be running it off a Profile AP1000M amp. The specs are below. The sub is a Memphis Power Refrence 12". The specs are below. Will I blow my sub because of the power of the amp? Should I just turn my gains down low and it should be fine?</p><p></p><p>Here is a pic:</p><p></p><p><a href="http://xs301.xs.to/xs301/06211/DSCN1740.JPG" target="_blank">http://xs301.xs.to/xs301/06211/DSCN1740.JPG</a></p><p></p><p>Specs of Profile AP1000M amp:</p><p></p><p># Peak Output Power(4 Ohms): 650W x 1</p><p></p><p># RMS Output Power(4 Ohms): 310W x 1</p><p></p><p># Peak Output Power(2 Ohms): 1000W x 1</p><p></p><p># RMS Output Power(2 Ohms): 500W x 1</p><p></p><p># Bridged RMS Output Power(4 Ohms): N/A</p><p></p><p># MOSFET Power Supply</p><p></p><p># Total Harmonic Distortion:</p><p></p><p># Signal/Noise Ratio: 103 dB</p><p></p><p># High/Low Level Converter(Male RCA)</p><p></p><p># Pre-Amp(RCA) Outputs</p><p></p><p># Variable Bass Boost@45Hz: 0 - 12 dB</p><p></p><p># 12dB/Octave Crossover: LP (Built-In)</p><p></p><p># Variable LP Crossover Frequemcy: 50 - 250 Hz</p><p></p><p># Variable HP Crossover Frequency: N/A</p><p></p><p># Bass Level Remote Control (16.4 ft)</p><p></p><p># Variable 12dB/Octave Subsonic Filter: 20 - 50 Hz</p><p></p><p># Variable Phase Control: 0 - 180¡Æ</p><p></p><p># Fuse(s): 2 X 30A</p><p></p><p># Dimensions (WxHxD): 13 5/8" X 2" x 10 1/4"</p><p></p><p># Power/Speaker Terminal Size(Gauge): 4/6</p><p></p><p>Specs of Memphis Power Refrence 12" sub:</p><p></p><p>* 2" Black anodized aluminum vented voice coil former</p><p></p><p>* High-strength wide roll surround</p><p></p><p>* Chrome plated vented basket</p><p></p><p>* Tough rubber top gasket</p><p></p><p>* RMS/Peak (W)- 250/450</p><p></p><p>* Sensitivity (dB) - 88</p><p></p><p>* Magnet Size (Oz) - 50</p><p></p><p>* Mounting Depth (in) - 5.4</p><p></p><p>Thanks!!!!</p></blockquote><p></p>
[QUOTE="Dynasty, post: 1784753, member: 567480"] This maybe a very stupid question, but is my sub SVC or DVC? I won this on ebay and the seller failed to mention which which one it is. I will be running it off a Profile AP1000M amp. The specs are below. The sub is a Memphis Power Refrence 12". The specs are below. Will I blow my sub because of the power of the amp? Should I just turn my gains down low and it should be fine? Here is a pic: [URL="http://xs301.xs.to/xs301/06211/DSCN1740.JPG"]http://xs301.xs.to/xs301/06211/DSCN1740.JPG[/URL] Specs of Profile AP1000M amp: # Peak Output Power(4 Ohms): 650W x 1 # RMS Output Power(4 Ohms): 310W x 1 # Peak Output Power(2 Ohms): 1000W x 1 # RMS Output Power(2 Ohms): 500W x 1 # Bridged RMS Output Power(4 Ohms): N/A # MOSFET Power Supply # Total Harmonic Distortion: # Signal/Noise Ratio: 103 dB # High/Low Level Converter(Male RCA) # Pre-Amp(RCA) Outputs # Variable Bass Boost@45Hz: 0 - 12 dB # 12dB/Octave Crossover: LP (Built-In) # Variable LP Crossover Frequemcy: 50 - 250 Hz # Variable HP Crossover Frequency: N/A # Bass Level Remote Control (16.4 ft) # Variable 12dB/Octave Subsonic Filter: 20 - 50 Hz # Variable Phase Control: 0 - 180¡Æ # Fuse(s): 2 X 30A # Dimensions (WxHxD): 13 5/8" X 2" x 10 1/4" # Power/Speaker Terminal Size(Gauge): 4/6 Specs of Memphis Power Refrence 12" sub: * 2" Black anodized aluminum vented voice coil former * High-strength wide roll surround * Chrome plated vented basket * Tough rubber top gasket * RMS/Peak (W)- 250/450 * Sensitivity (dB) - 88 * Magnet Size (Oz) - 50 * Mounting Depth (in) - 5.4 Thanks!!!! [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Subwoofers
Stupid Question, Easy Answer
Top
Menu
What's new
Forum list
