Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Stuck in protection mode with factory headunit and lc2i
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="van06TL" data-source="post: 8657576" data-attributes="member: 665774"><p>I recently bought a 2013 lesus gs350. Transfered everything from my old car. </p><p></p><p>Pioneer GM D9601</p><p></p><p>kicker 10cvx12 compvx 4ohm</p><p></p><p>some boss cap 10farads dont remeber specific model but it worked fine in old car. everything worked fine in old car</p><p></p><p>Set everything up in new car. Wire up the lc2i. Lc2i 12volt was tapped to a 12v at the stock amp wiring and now its connected to power wire at my pioneer amp. No change. Ground both on a factory ground spot and multiple other places. No change still in protection mode. I disconnected the sub from the amp since it kept making the constant heartbeat thump. (Will the pioneer amp go into protection mode if the sub wires are not connected? Did this so i dont blow my sub while troublesooting) </p><p></p><p>Im not getting 12v at the amp remote wire and im not sure how to fix that or if that should be the way it is comming from the lc2i loc. At one point i was getting 12v but that didnt change anything either. I assumed that the loc was working correctly because it has always been turning on the amp and cap. Havent made any adjustments to the Loc settings.</p><p></p><p>Tried without the cap first then added the cap and no change. Tried different rca cable. Tried different speaker wire. Tried different remote wire. Grounded to different places. Still in protection mode. Except for the loc which is new everything worked perfectly fine in my old setup.</p><p></p><p>not sure what else to do or where the problem is. Any help is appreciated. First time using an loc btw </p></blockquote><p></p>
[QUOTE="van06TL, post: 8657576, member: 665774"] I recently bought a 2013 lesus gs350. Transfered everything from my old car. Pioneer GM D9601 kicker 10cvx12 compvx 4ohm some boss cap 10farads dont remeber specific model but it worked fine in old car. everything worked fine in old car Set everything up in new car. Wire up the lc2i. Lc2i 12volt was tapped to a 12v at the stock amp wiring and now its connected to power wire at my pioneer amp. No change. Ground both on a factory ground spot and multiple other places. No change still in protection mode. I disconnected the sub from the amp since it kept making the constant heartbeat thump. (Will the pioneer amp go into protection mode if the sub wires are not connected? Did this so i dont blow my sub while troublesooting) Im not getting 12v at the amp remote wire and im not sure how to fix that or if that should be the way it is comming from the lc2i loc. At one point i was getting 12v but that didnt change anything either. I assumed that the loc was working correctly because it has always been turning on the amp and cap. Havent made any adjustments to the Loc settings. Tried without the cap first then added the cap and no change. Tried different rca cable. Tried different speaker wire. Tried different remote wire. Grounded to different places. Still in protection mode. Except for the loc which is new everything worked perfectly fine in my old setup. not sure what else to do or where the problem is. Any help is appreciated. First time using an loc btw [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Stuck in protection mode with factory headunit and lc2i
Top
Menu
Home
Refresh