Reply to thread

Message

<blockquote data-quote="trigga_b" data-source="post: 1230401" data-attributes="member: 564207">here go the specifications about the 2 ohm load.Specifications:Circuit system -- OTL (output transformerless) circuitPower supply -- PulseMaximum outputs -- 400 W x 2 (at 4 ohms)Maximum outputs -- 600 W x 2 (at 2 ohms)Maximum outputs -- 1200 W (monaural) at 4 ohmsRated outputs (at 14.4V) -- 200 W x 2 (20 - 20kHz, 0.1% THD, at 4 ohms)Rated outputs (at 14.4V) -- 250 W x 2 (20 - 20 kHz, 0.15% THD, at 2 ohms)Rated outputs (at 14.4V) -- 500 W (monaural) (20 - 20 kHz, 0.15% THD, at 4 ohms)Frequency response -- 5 Hz - 50 kHz (Â±3dB)Harmonic distortion -- 0.01% or less (at 1 kHz, 4 ohms)Input level adjustment range -- 0.3 - 6V (RCA pin jacks), 1.2 - 12V (High level)Low-pass filter -- 50 - 300 Hz, -12 dB/octLow boost -- 0 - 10 dB (40 Hz)Inputs -- RCA pin jacks, High level input connectorOutputs -- Speaker terminals, Through output pin jacksApproximate measurements -- 15-3/4&quot; x 2-1/4&quot; x 10-7/8&quot; (wxhxd) not including projecting parts and controlsSpeaker impedance -- 2 - 8 ohms (stereo)Speaker impedance -- 4 - 8 ohms (when used as a bridging amplifier)Power requirements -- 12 V DC car battery (negative ground)Power supply voltage -- 10.5 - 16 VCurrent drain -- 48 A (at 4 ohms, rated output)Weight -- Approx. 4.6 kg (10 lb 6 oz)Dimensions -- Approx. 400 x 55 x 276mm</blockquote>

[QUOTE="trigga_b, post: 1230401, member: 564207"] here go the specifications about the 2 ohm load. Specifications: Circuit system -- OTL (output transformerless) circuit Power supply -- Pulse Maximum outputs -- 400 W x 2 (at 4 ohms) Maximum outputs -- 600 W x 2 (at 2 ohms) Maximum outputs -- 1200 W (monaural) at 4 ohms Rated outputs (at 14.4V) -- 200 W x 2 (20 - 20kHz, 0.1% THD, at 4 ohms) Rated outputs (at 14.4V) -- 250 W x 2 (20 - 20 kHz, 0.15% THD, at 2 ohms) Rated outputs (at 14.4V) -- 500 W (monaural) (20 - 20 kHz, 0.15% THD, at 4 ohms) Frequency response -- 5 Hz - 50 kHz (Â±3dB) Harmonic distortion -- 0.01% or less (at 1 kHz, 4 ohms) Input level adjustment range -- 0.3 - 6V (RCA pin jacks), 1.2 - 12V (High level) Low-pass filter -- 50 - 300 Hz, -12 dB/oct Low boost -- 0 - 10 dB (40 Hz) Inputs -- RCA pin jacks, High level input connector Outputs -- Speaker terminals, Through output pin jacks Approximate measurements -- 15-3/4" x 2-1/4" x 10-7/8" (wxhxd) not including projecting parts and controls Speaker impedance -- 2 - 8 ohms (stereo) Speaker impedance -- 4 - 8 ohms (when used as a bridging amplifier) Power requirements -- 12 V DC car battery (negative ground) Power supply voltage -- 10.5 - 16 V Current drain -- 48 A (at 4 ohms, rated output) Weight -- Approx. 4.6 kg (10 lb 6 oz) Dimensions -- Approx. 400 x 55 x 276mm [/QUOTE]

Verification