Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Rockford Punch 800.2/MTX Thunder 6000 10's
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="echz" data-source="post: 7122" data-attributes="member: 541430"><p>I just picked up the Rockford Punch 800.2 and 2 10" MTX Thunder 6000's. The subs are 4 ohm and do 250 rms/500 peak i believe, and they are wired directly from the amp, so they should be being pushed at 200x2 if I'm thinking correctly. I don't know what's going on with them however, unless they are blown -- They seem to break up and not hit cleanly...They are in a sealed box, in a Ford Probe (hatchback). I'm using a Sony XPlod L-Cube series headunit that does 52x4 and has a separate sub out. I have the crossover on the amp set at ~60, and it's on Low Pass....I've played with the gains and tried everything i can think of, but to no avail. Can someone offer any insight to where my problem may be? Am I overamping these speakers? I don't believe that the system should be sounding as bad as it does...Any help is appreciated! //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif</p></blockquote><p></p>
[QUOTE="echz, post: 7122, member: 541430"] I just picked up the Rockford Punch 800.2 and 2 10" MTX Thunder 6000's. The subs are 4 ohm and do 250 rms/500 peak i believe, and they are wired directly from the amp, so they should be being pushed at 200x2 if I'm thinking correctly. I don't know what's going on with them however, unless they are blown -- They seem to break up and not hit cleanly...They are in a sealed box, in a Ford Probe (hatchback). I'm using a Sony XPlod L-Cube series headunit that does 52x4 and has a separate sub out. I have the crossover on the amp set at ~60, and it's on Low Pass....I've played with the gains and tried everything i can think of, but to no avail. Can someone offer any insight to where my problem may be? Am I overamping these speakers? I don't believe that the system should be sounding as bad as it does...Any help is appreciated! [IMG]//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif[/IMG] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Rockford Punch 800.2/MTX Thunder 6000 10's
Top
Menu
Home
Refresh