Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
Car Audio Build Logs
Rebuilding the prototype
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Papermaker85" data-source="post: 8592100" data-attributes="member: 572595"><p><img src="http://i.imgur.com/wkHzzHU.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" /></p><p></p><p><img src="http://i.imgur.com/9wTidar.jpg" alt="" class="fr-fic fr-dii fr-draggable " style="" /></p><p></p><p>The first driver was built strictly to sound good and have a ton of linear displacement that was able to do mid 140s at one ohm with a 3500 and high 140s with double the power. Still one of the best sounding woofers i've ever heard. Very realistic. Very transiant, very natural. Only downfall is that design was lower sensitivity that's normally measured at 1khz although it was extremely sensitive below 40 Hertz I still managed to do nearly the same number at both 38 Hertz and 50 hertz so there was no lack of top-end just a lack and overall efficiency. that's what happens when you get wide bandwidth and low distortion. //content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif at least untill i build the prequal to this driver which will improve the sensitivity without sacrificing anything but it's going to be extremely costly and tricky.</p><p></p><p>This particular coil is about 75% as long and slightly thicker. Xmax falls from 34mm to 22mm. This is still within Target in intended application and it still uses 10in Progressive spiders so it Still Remains a very linear driver .At this point i focused on lowering the mass increasing cone area while increasing the current carrying capability of the coil.</p><p></p><p>This gave me 2db higher 1w1m sensitivity rating and will give slightly less power compession at tuning and near the xover..</p></blockquote><p></p>
[QUOTE="Papermaker85, post: 8592100, member: 572595"] [IMG]http://i.imgur.com/wkHzzHU.jpg[/IMG] [IMG]http://i.imgur.com/9wTidar.jpg[/IMG] The first driver was built strictly to sound good and have a ton of linear displacement that was able to do mid 140s at one ohm with a 3500 and high 140s with double the power. Still one of the best sounding woofers i've ever heard. Very realistic. Very transiant, very natural. Only downfall is that design was lower sensitivity that's normally measured at 1khz although it was extremely sensitive below 40 Hertz I still managed to do nearly the same number at both 38 Hertz and 50 hertz so there was no lack of top-end just a lack and overall efficiency. that's what happens when you get wide bandwidth and low distortion. [IMG]//content.invisioncic.com/y282845/emoticons/wink.gif.608e3ea05f1a9f98611af0861652f8fb.gif[/IMG] at least untill i build the prequal to this driver which will improve the sensitivity without sacrificing anything but it's going to be extremely costly and tricky. This particular coil is about 75% as long and slightly thicker. Xmax falls from 34mm to 22mm. This is still within Target in intended application and it still uses 10in Progressive spiders so it Still Remains a very linear driver .At this point i focused on lowering the mass increasing cone area while increasing the current carrying capability of the coil. This gave me 2db higher 1w1m sensitivity rating and will give slightly less power compession at tuning and near the xover.. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Car Audio Build Logs
Rebuilding the prototype
Top
Menu
Home
Refresh