Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Quick Question Before install (please any input) .*Probably and Dumb Question*
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="xxrcm619xx" data-source="post: 8514172" data-attributes="member: 661855"><p>Good Evening Car Audiophile Enthusiasts.</p><p></p><p>Im about to start install the following equipment below listed. Now i have a somewhat an alright MB quart 4 channel amp that was given to me by a client for exchange purposes, and i have also acquired set of component of Morel Maximo 5 and Infinity Kappas 50.9C. The morel is set to be 4 Ohm and the Infinity is set to be 2 OHM and i made a mistake thinking that the Infinity's are 4 Ohm like usual speakers but i didn't notice it until this morning. Now will there be issues if i install these speakers with a different ohm load on 2 different channels? I know the MB quart amp is capable of running a 2 ohm load but will i get "clipping"/"distortion" issue when i get down to tuning this rig? I'm looking into buying a different set of components to replaces the infinity's for some morels too but I'm at a fork in the road and curious if i should buy speakers or an amp. Any Input helps. Thanks.</p><p></p><p>-Equipment.</p><p></p><p>Pioneer AVH-X3800BHS Head Unit</p><p></p><p>MB QUART 4.80x 4 Channel Amp ( Soon to be Alpine PDX-F4)</p><p></p><p>2x- JBL MS-A5001 Mono Block Amps</p><p></p><p>2x SunDown Audio SD3 10'S</p><p></p><p>Alpine SPR‑10TW (Front Pillar)</p><p></p><p>Morel Maxmio 5 5 1/4- 4 Ohm (Front Door)</p><p></p><p>infinity kappa 50.9cs- 2 Ohm (Rear Door)</p><p></p><p>Power: 0/1 Gauge Wire From Battery to Back Cab where it hooked to a Distribution box and 4 Gauge out to each amp.</p><p></p><p>Ground: 0/1 Ground on Frame.</p></blockquote><p></p>
[QUOTE="xxrcm619xx, post: 8514172, member: 661855"] Good Evening Car Audiophile Enthusiasts. Im about to start install the following equipment below listed. Now i have a somewhat an alright MB quart 4 channel amp that was given to me by a client for exchange purposes, and i have also acquired set of component of Morel Maximo 5 and Infinity Kappas 50.9C. The morel is set to be 4 Ohm and the Infinity is set to be 2 OHM and i made a mistake thinking that the Infinity's are 4 Ohm like usual speakers but i didn't notice it until this morning. Now will there be issues if i install these speakers with a different ohm load on 2 different channels? I know the MB quart amp is capable of running a 2 ohm load but will i get "clipping"/"distortion" issue when i get down to tuning this rig? I'm looking into buying a different set of components to replaces the infinity's for some morels too but I'm at a fork in the road and curious if i should buy speakers or an amp. Any Input helps. Thanks. -Equipment. Pioneer AVH-X3800BHS Head Unit MB QUART 4.80x 4 Channel Amp ( Soon to be Alpine PDX-F4) 2x- JBL MS-A5001 Mono Block Amps 2x SunDown Audio SD3 10'S Alpine SPR‑10TW (Front Pillar) Morel Maxmio 5 5 1/4- 4 Ohm (Front Door) infinity kappa 50.9cs- 2 Ohm (Rear Door) Power: 0/1 Gauge Wire From Battery to Back Cab where it hooked to a Distribution box and 4 Gauge out to each amp. Ground: 0/1 Ground on Frame. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Quick Question Before install (please any input) .*Probably and Dumb Question*
Top
Menu
Home
Refresh