Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
Popping, feedback noise when switching headunit on.
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Oreos_ZA" data-source="post: 8489997" data-attributes="member: 669480"><p>I have tried everything yet I have not been able to fix a very irritating issue, the left RCA channel that is sent to my amp sends a bad feedback "popping" thump whenever I ex- start car (switches headunit off and on - eject CD - change certain EQ features on my headunit or turn volume from anything to 0 value, as soon as it hits 0 it will pop, everything should be grounded perfectly, I hardly doubt I have missed something my set-up:</p><p></p><p>Headunit (after market Pioneer) powering 2 x 5" pioneer speakers, headunit is grounded to the engine bay frame via a screw mounting point on the back of the headunit, solid ground.</p><p></p><p>4 Channel Amp, grounded to rear frame, 4 channels 80 Watt RMS each running -</p><p></p><p>2 x 6x9 (4Ohms) 80 Watts rated @ RMS each running on channel 1 + 2.</p><p></p><p>1 x 12" 300Watt RMS rated Sub running on channel 3 + 4 bridged.</p><p></p><p>Right now I run my left channel to my channel 3 + 4 on my amp so when it pops it's just my sub, so I dont damage my 6x9's as I figured my sub is the most hardy, anyways -</p><p></p><p>I have had a previous issue where when my car is switched on there is a lot of coil whine noise, high pitches when I revved my car it would change pitch and so on, I fixed this by getting a small thin copper speaker wire and basically grounding my red RCA connection on the back of the headunit output, I tried grounding both RCA's but it only works with one, and the popping will only happen if I have the left channel (white RCA) plugged into the head unit, otherwise it is silent. Any help? Any questions or info you need to know? My ground wire's are hectic for the amp,a massive 8 gauge and even the silly headunit I grounded desperately to the engine bay with a nice 10 gauge encase it was a ground related issue with the popping. Do I need to reduce the high-level output voltage from my headunit to amp or what?! I am clueless =/ Any help would be greatly appreciated!</p><p></p><p>Kind regards</p><p></p><p>-Oreos</p></blockquote><p></p>
[QUOTE="Oreos_ZA, post: 8489997, member: 669480"] I have tried everything yet I have not been able to fix a very irritating issue, the left RCA channel that is sent to my amp sends a bad feedback "popping" thump whenever I ex- start car (switches headunit off and on - eject CD - change certain EQ features on my headunit or turn volume from anything to 0 value, as soon as it hits 0 it will pop, everything should be grounded perfectly, I hardly doubt I have missed something my set-up: Headunit (after market Pioneer) powering 2 x 5" pioneer speakers, headunit is grounded to the engine bay frame via a screw mounting point on the back of the headunit, solid ground. 4 Channel Amp, grounded to rear frame, 4 channels 80 Watt RMS each running - 2 x 6x9 (4Ohms) 80 Watts rated @ RMS each running on channel 1 + 2. 1 x 12" 300Watt RMS rated Sub running on channel 3 + 4 bridged. Right now I run my left channel to my channel 3 + 4 on my amp so when it pops it's just my sub, so I dont damage my 6x9's as I figured my sub is the most hardy, anyways - I have had a previous issue where when my car is switched on there is a lot of coil whine noise, high pitches when I revved my car it would change pitch and so on, I fixed this by getting a small thin copper speaker wire and basically grounding my red RCA connection on the back of the headunit output, I tried grounding both RCA's but it only works with one, and the popping will only happen if I have the left channel (white RCA) plugged into the head unit, otherwise it is silent. Any help? Any questions or info you need to know? My ground wire's are hectic for the amp,a massive 8 gauge and even the silly headunit I grounded desperately to the engine bay with a nice 10 gauge encase it was a ground related issue with the popping. Do I need to reduce the high-level output voltage from my headunit to amp or what?! I am clueless =/ Any help would be greatly appreciated! Kind regards -Oreos [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
Popping, feedback noise when switching headunit on.
Top
Menu
Home
Refresh