Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
General Car Audio
Plans for my new system
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="rynecampbell18" data-source="post: 7015548" data-attributes="member: 626390"><p>Ok so my birthday is coming up and i've decided to ask for an upgrade from my current system. My current system is pretty basic, just a diamond d315 2 ohm sub in a ported box(not even sure what the specs on it are lol) powered by a kenwood 8104d mono amp wired to 2 ohms. So it's pushing around 500 rms and sounds pretty good but it's not loud enough for me. I want your opinion on this small idea i had for my new system. I'm planning on upgrading my 8104d to 2 kenwood 9104d which put out about 900 rms at 2 ohms, I'll have those two amps powering some apline type x's in a ported box rated to the recommended specs of course. The next part is the part i'm not so sure about because i'm still pretty new to car audio. This setup is obviously going to be drawing a lot of power from my battery and to solve this problem i was thinking about getting a 2 farad cap, but i'm not too clear on if that will solve the power problem. My car has a stock battery that is pretty weak as well as a stock alternator. Btw the apline 10's im getting are rated at 1000wrms at 2 ohms. I figure the 900 rms amps might be a little underpowering to the type x's but i'm trying to be on a budget. I did some research on capacitors and found that .5 farads=500 rms so i figure like 2000 rms i need a 2 farad cap? I might even consider swapping the 10" aplines for 12" diamond d9's but it would hurt the budget a bit more. Again give me some feedback on what you think about the setup or alternatives that would cost me the same and be a better deal.</p></blockquote><p></p>
[QUOTE="rynecampbell18, post: 7015548, member: 626390"] Ok so my birthday is coming up and i've decided to ask for an upgrade from my current system. My current system is pretty basic, just a diamond d315 2 ohm sub in a ported box(not even sure what the specs on it are lol) powered by a kenwood 8104d mono amp wired to 2 ohms. So it's pushing around 500 rms and sounds pretty good but it's not loud enough for me. I want your opinion on this small idea i had for my new system. I'm planning on upgrading my 8104d to 2 kenwood 9104d which put out about 900 rms at 2 ohms, I'll have those two amps powering some apline type x's in a ported box rated to the recommended specs of course. The next part is the part i'm not so sure about because i'm still pretty new to car audio. This setup is obviously going to be drawing a lot of power from my battery and to solve this problem i was thinking about getting a 2 farad cap, but i'm not too clear on if that will solve the power problem. My car has a stock battery that is pretty weak as well as a stock alternator. Btw the apline 10's im getting are rated at 1000wrms at 2 ohms. I figure the 900 rms amps might be a little underpowering to the type x's but i'm trying to be on a budget. I did some research on capacitors and found that .5 farads=500 rms so i figure like 2000 rms i need a 2 farad cap? I might even consider swapping the 10" aplines for 12" diamond d9's but it would hurt the budget a bit more. Again give me some feedback on what you think about the setup or alternatives that would cost me the same and be a better deal. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
General Car Audio
Plans for my new system
Top
Menu
Home
Refresh