Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Wiring, Electrical & Installation
New Installation - 2x SKAR Audio SDR-12 /w Rockville DB15
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Kielthalin" data-source="post: 8823717" data-attributes="member: 687500"><p>Just curious if I got everything I need for an install. This is just a daily driver vehicle, a small sedan. Just looking for suggestions.</p><p>2x Skar Audio SDR-12 Dual 2ohm (600Wrms each) - Final Impedance = 2 ohm (series/parallel) in a 2.5 ft^3 Sealed enclosure (each sub in separate 1.25 chamber). Wired using 8AWG speaker wire to the amp. Might have to use 12AWG from the speaker box terminals to the amp if the 8AWG won't fit. I think I had that problem last time I used the amp.</p><p></p><p>Rockville DB15 amp - 2ohm rating is 1500W. I think these only dyno to around 1200W? This amp is from another setup. I have 1/0 OFC in a 17' run. The amp has a 150A fuse and I will be clamping to see the draw once setup. Curious if I will need another run of 1/0.</p><p></p><p>The alternator is stock, rated to 120A. Big three completed /w 1/0 bare copper cables (welding wire).</p><p></p><p>If the electrical give me issues (lights dimming etc.), other than running another 1/0 cable to the amp, what else could I do?</p></blockquote><p></p>
[QUOTE="Kielthalin, post: 8823717, member: 687500"] Just curious if I got everything I need for an install. This is just a daily driver vehicle, a small sedan. Just looking for suggestions. 2x Skar Audio SDR-12 Dual 2ohm (600Wrms each) - Final Impedance = 2 ohm (series/parallel) in a 2.5 ft^3 Sealed enclosure (each sub in separate 1.25 chamber). Wired using 8AWG speaker wire to the amp. Might have to use 12AWG from the speaker box terminals to the amp if the 8AWG won't fit. I think I had that problem last time I used the amp. Rockville DB15 amp - 2ohm rating is 1500W. I think these only dyno to around 1200W? This amp is from another setup. I have 1/0 OFC in a 17' run. The amp has a 150A fuse and I will be clamping to see the draw once setup. Curious if I will need another run of 1/0. The alternator is stock, rated to 120A. Big three completed /w 1/0 bare copper cables (welding wire). If the electrical give me issues (lights dimming etc.), other than running another 1/0 cable to the amp, what else could I do? [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Wiring, Electrical & Installation
New Installation - 2x SKAR Audio SDR-12 /w Rockville DB15
Top
Menu
Home
Refresh