Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Equipment
Amplifiers
need a good reliable 4 channel amp
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="SuBXeRo" data-source="post: 400105" data-attributes="member: 553381"><p>this is alittle under the rms but its a good amp</p><p></p><p><a href="http://www.cbrstereo.com/index.asp?PageAction=VIEWPROD&amp;ProdID=835" target="_blank">http://www.cbrstereo.com/index.asp?PageAction=VIEWPROD&amp;ProdID=835</a></p><p></p><p>its a rockford fosgate 551x</p><p></p><p>70 watts RMS x 4 at 4 ohms</p><p></p><p>140 watts RMS x 4 at 2 ohms</p><p></p><p>275 watts RMS x 2 in bridged mode at 4 ohms</p><p></p><p>2-, 3-, or 4-channel output</p><p></p><p>4-ohm stable in bridged mode</p><p></p><p>Tri-Way capable</p><p></p><p>requires 4-gauge power and ground leads — wiring and hardware not included with amplifier</p><p></p><p>MOSFET power supply and output devices</p><p></p><p>front and rear 50-250 Hz high-pass/low-pass crossovers, 24 dB/octave slopes</p><p></p><p>MEHSA mounting technology increases the heat transfer from the MOSFET output devices to the heat sink, for higher power output, lower operating temperatures, and greater reliability</p><p></p><p>TOPAZ — noise-killing differential inputs that eliminate 80% of ground loop noise</p><p></p><p>Trans•ana circuitry keeps preamp voltages low and signal paths simple for outstanding audio quality</p><p></p><p>NOMAD — advanced protection circuitry for "intelligent" shutdown protection</p><p></p><p>wired remote control included for fingertip control of Punch Bass (for 0-18 dB of bass boost at 45 Hz)</p><p></p><p>preamp-level (RCA) inputs</p><p></p><p>preamp-level (RCA) outputs</p><p></p><p>12-1/8"W x 2-3/8"H x 9-7/8"D</p><p></p><p>should be suffient but if u wanna invest a lil more there a good 4 channel alpine amp i believe thats 80 watts a channel</p></blockquote><p></p>
[QUOTE="SuBXeRo, post: 400105, member: 553381"] this is alittle under the rms but its a good amp [URL="http://www.cbrstereo.com/index.asp?PageAction=VIEWPROD&ProdID=835"]http://www.cbrstereo.com/index.asp?PageAction=VIEWPROD&ProdID=835[/URL] its a rockford fosgate 551x 70 watts RMS x 4 at 4 ohms 140 watts RMS x 4 at 2 ohms 275 watts RMS x 2 in bridged mode at 4 ohms 2-, 3-, or 4-channel output 4-ohm stable in bridged mode Tri-Way capable requires 4-gauge power and ground leads — wiring and hardware not included with amplifier MOSFET power supply and output devices front and rear 50-250 Hz high-pass/low-pass crossovers, 24 dB/octave slopes MEHSA mounting technology increases the heat transfer from the MOSFET output devices to the heat sink, for higher power output, lower operating temperatures, and greater reliability TOPAZ — noise-killing differential inputs that eliminate 80% of ground loop noise Trans•ana circuitry keeps preamp voltages low and signal paths simple for outstanding audio quality NOMAD — advanced protection circuitry for "intelligent" shutdown protection wired remote control included for fingertip control of Punch Bass (for 0-18 dB of bass boost at 45 Hz) preamp-level (RCA) inputs preamp-level (RCA) outputs 12-1/8"W x 2-3/8"H x 9-7/8"D should be suffient but if u wanna invest a lil more there a good 4 channel alpine amp i believe thats 80 watts a channel [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Equipment
Amplifiers
need a good reliable 4 channel amp
Top
Menu
Home
Refresh