Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Help
Enclosure Design & Construction
My first thread----HELP!
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="slowfive0" data-source="post: 1274271" data-attributes="member: 564634"><p>Hey guys,</p><p></p><p>Great site! I'm a newbie attempting my first box build. Vehicle is a 2000 Chevy Ext. cab pickup. I'm building the box to go under the rear seat to house 2 12's. Here is my problem and question.</p><p></p><p>I don't know what the subwoofer requirements are? They are 12", Have MD2 on the cone. The sticker on the back of the magnet says:</p><p></p><p>Impact High Performance Drivers</p><p></p><p>There is a big M for a symbol?</p><p></p><p>74792 / MD2128</p><p></p><p>These are 10 years old if not a little more.</p><p></p><p>The box I measured up (haven't made it yet) will have approximately 1.25 cu/ft per speaker. I was leaning towards sealed just because of my inexperience and not knowing what the speakers were designed for.</p><p></p><p>What would you guys recommend for a volume and have you ever heard of these speakers? (I'm not against ported if I can make it work without knowing the speaker requirements.)</p><p></p><p>Also, should I divide the box up in the middle (separate chamber for each speaker)????</p><p></p><p>Thank you for any input! //content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif</p><p></p><p>P.S. I will be powering it up with a Rockford Fosgate amp (200) bridged---roughly same age as speakers.</p></blockquote><p></p>
[QUOTE="slowfive0, post: 1274271, member: 564634"] Hey guys, Great site! I'm a newbie attempting my first box build. Vehicle is a 2000 Chevy Ext. cab pickup. I'm building the box to go under the rear seat to house 2 12's. Here is my problem and question. I don't know what the subwoofer requirements are? They are 12", Have MD2 on the cone. The sticker on the back of the magnet says: Impact High Performance Drivers There is a big M for a symbol? 74792 / MD2128 These are 10 years old if not a little more. The box I measured up (haven't made it yet) will have approximately 1.25 cu/ft per speaker. I was leaning towards sealed just because of my inexperience and not knowing what the speakers were designed for. What would you guys recommend for a volume and have you ever heard of these speakers? (I'm not against ported if I can make it work without knowing the speaker requirements.) Also, should I divide the box up in the middle (separate chamber for each speaker)???? Thank you for any input! [IMG]//content.invisioncic.com/y282845/emoticons/biggrin.gif.d71a5d36fcbab170f2364c9f2e3946cb.gif[/IMG] P.S. I will be powering it up with a Rockford Fosgate amp (200) bridged---roughly same age as speakers. [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Help
Enclosure Design & Construction
My first thread----HELP!
Top
Menu
Home
Refresh