Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Log in / Join
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
Car Audio Build Logs
My first "Active" "SQ'ish" build attempt.
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="ThxOne" data-source="post: 8717277" data-attributes="member: 675210"><p>A few days back I went into the GUI for the DSP and disabled the delay for all the speakers. The drivers door is louder but it sounds strange after being so used to having time alignment.</p><p></p><p>No rain is forecast for tomorrow so I want to hook up my RCA cables. I only had one pair hooked up when I had my temporary pioneer single din hooked up and for some reason I only have one set hooked up now from the Kenwood into the DSP. My Knu Koncepts Krystal RCA's are still in the dash and still run all the way to the back. They are a 4 channel set that I had going directly to the US Acoustics at one time. Plus the single pair running currently to the DSP for a total of all 6 channels of RCA's. Again, no idea why they are not all hooked up. </p><p><strong></strong></p><p><strong>I am still trying to figure out gains. What messes me up is the DSP in the middle. I can get my head units max clean volume with no EQ or BASS Boost or Loudness. Now insert the DSP... No EQ, all Flat, crossovers set roughly, Delays set, All Volume Outputs Full?? - Amplifiers, everything full pass, no bass boost, bass knob max, set gains to max unclipped output with appropriate -??Db tones. Do I now go back to the DSP, lower all the levels and bust out the RTA with pink noise? What do I set the volumes for in the DSP? They go up to 0db. If I set the highs (tweeters) amp with a -5db tone, the mids with a -10db and the sub with a -15db.... where do I set the DSP volume for each speaker set? Do I set them at 0db (max) and just cut via the EQ's??? I am still so confused.</strong></p></blockquote><p></p>
[QUOTE="ThxOne, post: 8717277, member: 675210"] A few days back I went into the GUI for the DSP and disabled the delay for all the speakers. The drivers door is louder but it sounds strange after being so used to having time alignment. No rain is forecast for tomorrow so I want to hook up my RCA cables. I only had one pair hooked up when I had my temporary pioneer single din hooked up and for some reason I only have one set hooked up now from the Kenwood into the DSP. My Knu Koncepts Krystal RCA's are still in the dash and still run all the way to the back. They are a 4 channel set that I had going directly to the US Acoustics at one time. Plus the single pair running currently to the DSP for a total of all 6 channels of RCA's. Again, no idea why they are not all hooked up. [B] I am still trying to figure out gains. What messes me up is the DSP in the middle. I can get my head units max clean volume with no EQ or BASS Boost or Loudness. Now insert the DSP... No EQ, all Flat, crossovers set roughly, Delays set, All Volume Outputs Full?? - Amplifiers, everything full pass, no bass boost, bass knob max, set gains to max unclipped output with appropriate -??Db tones. Do I now go back to the DSP, lower all the levels and bust out the RTA with pink noise? What do I set the volumes for in the DSP? They go up to 0db. If I set the highs (tweeters) amp with a -5db tone, the mids with a -10db and the sub with a -15db.... where do I set the DSP volume for each speaker set? Do I set them at 0db (max) and just cut via the EQ's??? I am still so confused.[/B] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Car Audio Build Logs
My first "Active" "SQ'ish" build attempt.
Top
Menu
Home
Refresh