Menu
Forum
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Car Audio Discussion
General Car Audio
Car Audio Build Logs
Car Audio Equipment
Subwoofers
Speakers
Amplifiers
Head Units
Car Audio Help
Wiring, Electrical and Installation
Enclosure Design & Construction
Car Audio Classifieds
Car Audio Classifieds
Car Audio Wanted
Classifieds Member Feedback
Gallery
New media
New comments
Search media
SHOP
Shop Head Units
Shop Amplifiers
Shop Speakers
Shop Subwoofers
Shop eBay Car Audio
Test
Forum
Search
Search titles only
Search titles only
Log in / Join
Search
Search titles only
Search titles only
What's new
New posts
Live Activity
Search forums
Members
Registered members
Classifieds Member Feedback
Menu
Reply to thread
Forum
Car Audio Discussion
Car Audio Build Logs
My first "Active" "SQ'ish" build attempt.
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="ThxOne" data-source="post: 8660742" data-attributes="member: 675210"><p>Ok... it is time to get some info and start the planning!!! @shredder2 this is what I have to work with. What specifically and exactly do you recommend for this exact setup? I want to do a single slot port. I listen to bass music with frequencies from the mid 20's and up (20% of the time) to all other music (80% of the time) up to 70ish hertz (Drums, Kick Drums, Bass Guitar, Piano, Jazz Instruments and Acoustic Instruments). I will run the Dayton single 10 all by itself powered by the US Acoustics Mike amplifier. This is not about loud but I imagine that will be a welcome side effect of the sub/amp combo. I want the sub centered on the baffle facing the rear of the trunk with a max of 14in tall from floor to top of the enclosure. I have the skills to build the enclosure with bracing and 45's. Rear deck 6x9 speakers will be removed. Amps will be on an amp rack. I now have all of the specs and they are as follows:</p><p></p><ol> <li data-xf-list-type="ol"><strong><u>Pontiac G6 GT Coupe</u> - </strong><br /> <br /> <br /> <strong>Interior Dimensions</strong><br /> <u>Passenger Volume (ft³) 90.1</u><br /> <strong>Cargo Area Dimensions</strong><br /> <br /> <br /> <br /> <u><strong>Trunk Volume</strong> (ft³) 12.0</u><br /> <br /> <br /> </li> <li data-xf-list-type="ol">Subwoofer - Dayton Audio UM10-22<br /> <br /> Impedance<br /> <br /> 2+2 ohms<br /> <br /> <br /> Re<br /> <br /> 3.2 ohms<br /> <br /> <br /> Le<br /> <br /> 1.28 mH @ 1 kHz<br /> <br /> <br /> Fs<br /> <br /> 26.9 Hz<br /> <br /> <br /> Qms<br /> <br /> 3.08<br /> <br /> <br /> Qes<br /> <br /> 0.59<br /> <br /> <br /> Qts<br /> <br /> 0.49<br /> <br /> <br /> Mms<br /> <br /> 227g<br /> <br /> <br /> Cms<br /> <br /> 0.15 mm/N<br /> <br /> <br /> Sd<br /> <br /> 327.8 cm²<br /> <br /> <br /> Vd<br /> <br /> 622.8 cm³<br /> <br /> <br /> BL<br /> <br /> 14.5 Tm<br /> <br /> <br /> Vas<br /> <br /> 23.5 liters<br /> <br /> <br /> Xmax<br /> <br /> 19 mm<br /> <br /> <br /> VC Diameter<br /> <br /> 63.5 mm<br /> <br /> <br /> SPL<br /> <br /> 84.8 dB @ 2.83V/1m<br /> <br /> <br /> RMS Power Handling<br /> <br /> 500 watts<br /> <br /> <br /> <br /> <br /> </li> <li data-xf-list-type="ol">Amp - US Acoustics Mike 1500w RMS @ 1ohm - I will be running at 1ohm and there will be a second battery in the trunk.<br /> <br /> <br /> <br /> <br /> <br /> <br /> </li> </ol></blockquote><p></p>
[QUOTE="ThxOne, post: 8660742, member: 675210"] Ok... it is time to get some info and start the planning!!! @shredder2 this is what I have to work with. What specifically and exactly do you recommend for this exact setup? I want to do a single slot port. I listen to bass music with frequencies from the mid 20's and up (20% of the time) to all other music (80% of the time) up to 70ish hertz (Drums, Kick Drums, Bass Guitar, Piano, Jazz Instruments and Acoustic Instruments). I will run the Dayton single 10 all by itself powered by the US Acoustics Mike amplifier. This is not about loud but I imagine that will be a welcome side effect of the sub/amp combo. I want the sub centered on the baffle facing the rear of the trunk with a max of 14in tall from floor to top of the enclosure. I have the skills to build the enclosure with bracing and 45's. Rear deck 6x9 speakers will be removed. Amps will be on an amp rack. I now have all of the specs and they are as follows: [LIST=1][*][B][U]Pontiac G6 GT Coupe[/U] - [/B] [B]Interior Dimensions[/B] [U]Passenger Volume (ft³) 90.1[/U] [B]Cargo Area Dimensions[/B] [U][B]Trunk Volume[/B] (ft³) 12.0[/U] [*]Subwoofer - Dayton Audio UM10-22 Impedance 2+2 ohms Re 3.2 ohms Le 1.28 mH @ 1 kHz Fs 26.9 Hz Qms 3.08 Qes 0.59 Qts 0.49 Mms 227g Cms 0.15 mm/N Sd 327.8 cm² Vd 622.8 cm³ BL 14.5 Tm Vas 23.5 liters Xmax 19 mm VC Diameter 63.5 mm SPL 84.8 dB @ 2.83V/1m RMS Power Handling 500 watts [*]Amp - US Acoustics Mike 1500w RMS @ 1ohm - I will be running at 1ohm and there will be a second battery in the trunk. [/LIST] [/QUOTE]
Insert quotes…
Verification
Post reply
Forum
Car Audio Discussion
Car Audio Build Logs
My first "Active" "SQ'ish" build attempt.
Top
Menu
Home
Refresh